View ADUC841BCP8-3_659102.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MicroConverter(R) 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU ADuC841/ADuC842/ADuC843
FEATURES
Pin compatable ugrade of ADuC812/ADuC831/ADuC832 Increased performance Single-cycle 20 MIPS 8052 core High speed 420 kSPS 12-bit ADC Increased memory Up to 62 kBytes on-chip Flash/EE program memory 4 kBytes on-chip Flash/EE data memory In-circuit reprogrammable Flash/EE, 100 year retention, 100 kCycle endurance 2304 bytes on-chip data RAM Smaller package 8 mm x 8 mm chip scale package 52-lead PQFP--pin compatable upgrade Analog I/O 8-channel, 420 kSPS high accuracy, 12-bit ADC On-chip, 15 ppm/C voltage reference DMA controller, high speed ADC-to-RAM capture Two 12-bit voltage output DACs1 Dual output PWM - DACs On-chip temperature monitor function 8052 based core 8051 compatible instruction set (20 MHz max) High performance single-cycle core 32 kHz external crystal, on-chip programmable PLL 12 interrupt sources, 2 priority levels Dual data pointers, extended 11-bit stack pointer On-chip peripherals Time interval counter (TIC) UART, I2C(R), and SPI(R) Serial I/O Watchdog timer (WDT) Power supply monitor (PSM) Power Normal: 4.5 mA @ 3 V (core CLK = 2.098 MHz) Power-down: 10 A @ 3 V2 Development tools Low cost, comprehensive development system incorporating nonintrusive single-pin emulation, IDE based assembly and C source debugging
FUNCTIONAL BLOCK DIAGRAM
ADuC841/ADuC842/ADuC843
12-BIT DAC BUF DAC1
ADC0 ADC1 T/H 12-BIT ADC
12-BIT DAC
BUF
DAC1
MUX ADC5 ADC6 ADC7 HARDWARE CALIBRATON TEMP SENSOR
16-BIT - DAC 16-BIT - DAC MUX 16-BIT PWM PWM1
PWM0
16-BIT PWM
20 MIPS 8052 BASED MCU WITH ADDITIONAL PERIPHERALS PLL2 62 kBYTES FLASH/EE PROGRAM MEMORY 4 kBYTES FLASH/EE DATA MEMORY 2304 BYTES USER RAM 3 x 16 BIT TIMERS 1 x REAL TIME CLOCK OSC 4 x PARALLEL PORTS POWER SUPPLY MON WATCHDOG TIMER UART, I2 C, AND SPI SERIAL I/O
03260-0-001
INTERNAL BAND GAP VREF
CREF
XTAL1
XTAL2
Figure 1.
GENERAL DESCRIPTION
The ADuC841/ADuC842/ADuC843 are complete smart transducer front ends, that integrates a high performance selfcalibrating multichannel ADC, a dual DAC, and an optimized single-cycle 20 MHz 8-bit MCU (8051 instruction set compatible) on a single chip. The ADuC841 and ADuC842 are identical with the exception of the clock oscillator circuit; the ADuC841 is clocked directly from an external crystal up to 20 MHz whereas the ADuC842 uses a 32 kHz crystal with an on-chip PLL generating a programmable core clock up to 16.78 MHz. The ADuC843 is identical to the ADuC842 except that the ADuC843 has no analog DAC outputs. The microcontroller is an optimized 8052 core offering up to 20 MIPS peak performance. Three different memory options are available offering up to 62 kBytes of nonvolatile Flash/EE program memory. Four kBytes of nonvolatile Flash/EE data memory, 256 bytes RAM, and 2 kBytes of extended RAM are also integrated on-chip. (continued on page 15)
APPLICATIONS
Optical networking--laser power control Base station systems Precision instrumentation, smart sensors Transient capture systems DAS and communications systems
1 2
ADuC841/ADuC842 only. ADuC842/ADuC843 only, ADuC841 driven directly by external crystal.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 (c) 2003 Analog Devices, Inc. All rights reserved.
ADuC841/ADuC842/ADuC843 TABLE OF CONTENTS
Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 8 ESD Caution.................................................................................. 8 Pin Configurations and Functional Descriptions ........................ 9 Terminology .................................................................................... 11 ADC Specifications .................................................................... 11 DAC Specifications..................................................................... 11 Typical Performance Characteristics ........................................... 12 Functional Description .................................................................. 16 8052 Instruction Set ................................................................... 16 Other Single-Cycle Core Features ............................................ 18 Memory Organization ............................................................... 19 Special Function Registers (SFRs)............................................ 20 Accumulator SFR (ACC)........................................................... 21 Special Function Register Banks .............................................. 22 ADC Circuit Information.......................................................... 23 Calibrating the ADC .................................................................. 30 Nonvolatile Flash/EE Memory ................................................. 31 Using Flash/EE Data Memory .................................................. 34 User Interface to On-Chip Peripherals.................................... 38 On-Chip PLL............................................................................... 41 Pulse-Width Modulator (PWM).............................................. 42 Serial Peripheral Interface (SPI)............................................... 45 I2C Compatible Interface........................................................... 48 Dual Data Pointer....................................................................... 51 Power Supply Monitor ............................................................... 52 Watchdog Timer......................................................................... 53 Time Interval Counter (TIC).................................................... 54 8052 Compatible On-Chip Peripherals................................... 57 Timer/Counter 0 and 1 Operating Modes.............................. 62 Timer/Counter Operating Modes............................................ 64 UART Serial Interface................................................................ 65 SBUF ............................................................................................ 65 Interrupt System ......................................................................... 70 Hardware Design Considerations ............................................ 72 Other Hardware Considerations.............................................. 76 Development Tools .................................................................... 77 QuickStart Development System ............................................. 77 Timing Specifications, , .................................................................. 78 Outline Dimensions ....................................................................... 86 Ordering Guides......................................................................... 87
REVISION HISTORY
Revision 0: Initial Version
Rev. 0 | Page 2 of 88
ADuC841/ADuC842/ADuC843 SPECIFICATIONS1
Table 1. AVDD = DVDD = 2.7 V to 3.6 V or 4.75 V to 5.25 V; VREF = 2.5 V internal reference, fCORE = 16.78 MHz @ 5 V 8.38 MHz @ 3 V; all specifications TA = TMIN to TMAX, unless otherwise noted
Parameter ADC CHANNEL SPECIFICATIONS DC ACCURACY2, 3 VDD = 5 V VDD = 3 V Unit Test Conditions/Comments fSAMPLE = 120 kHz, see the Typical Performance Characteristics for typical performance at other values of fSAMPLE 12 1 0.3 +1/-0.9 0.3 2 +1.5/-0.9 1 3 1 3 1 12 1 0.3 +1/-0.9 0.3 1.5 +1.5/-0.9 1 2 1 2 1 Bits LSB max LSB typ LSB max LSB typ LSB max LSB max LSB typ LSB max LSB typ LSB max LSB typ fIN = 10 kHz sine wave fSAMPLE = 120 kHz 71 -85 -85 -80 0 to VREF 1 32 700 -1.4 1.5 71 -85 -85 -80 0 to VREF 1 32 700 -1.4 1.5 dB typ dB typ dB typ dB typ V A max pF typ mV typ mV/C typ C typ 2.5 V internal reference 2.5 V internal reference 1 V external reference 1 V external reference ADC input is a dc voltage
Resolution Integral Nonlinearity Differential Nonlinearity Integral Nonlinearity4 Differential Nonlinearity4 Code Distribution CALIBRATED ENDPOINT ERRORS5, 6 Offset Error Offset Error Match Gain Error Gain Error Match DYNAMIC PERFORMANCE Signal-to-Noise Ratio (SNR)7 Total Harmonic Distortion (THD) Peak Harmonic or Spurious Noise Channel-to-Channel Crosstalk8 ANALOG INPUT Input Voltage Range Leakage Current Input Capacitance TEMPERATURE SENSOR9 Voltage Output at 25C Voltage TC Accuracy DAC CHANNEL SPECIFICATIONS Internal Buffer Enabled ADuC841/ADuC842 Only DC ACCURACY10 Resolution Relative Accuracy Differential Nonlinearity11 Offset Error Gain Error Gain Error Mismatch ANALOG OUTPUTS Voltage Range_0 Voltage Range_1 Output Impedance
Internal/External 2.5 V VREF DAC load to AGND RL = 10 k, CL = 100 pF
12 3 -1 1/2 50 1 1 0.5 0 to VREF 0 to VDD 0.5
12 3 -1 1/2 50 1 1 0.5 0 to VREF 0 to VDD 0.5
Bits LSB typ LSB max LSB typ mV max % max % typ % typ V typ V typ typ
Guaranteed 12-bit monotonic VREF range AVDD range VREF range % of full-scale on DAC1 DAC VREF = 2.5 V DAC VREF = VDD
Rev. 0 | Page 3 of 88
ADuC841/ADuC842/ADuC843
Parameter DAC AC CHARACTERISTICS Voltage Output Settling Time Digital-to-Analog Glitch Energy DAC CHANNEL SPECIFICATIONS12, 13 Internal Buffer Disabled ADuC841/ADuC842 Only DC ACCURACY10 Resolution Relative Accuracy Differential Nonlinearity11 Offset Error Gain Error Gain Error Mismatch4 ANALOG OUTPUTS Voltage Range_0 REFERENCE INPUT/OUTPUT REFERENCE OUTPUT14 Output Voltage (VREF) Accuracy Power Supply Rejection Reference Temperature Coefficient Internal VREF Power-On Time EXTERNAL REFERENCE INPUT15 Voltage Range (VREF) 4 Input Impedance Input Leakage POWER SUPPLY MONITOR (PSM) DVDD Trip Point Selection Range VDD = 5 V 15 10 VDD = 3 V 15 10 Unit s typ nV-sec typ Test Conditions/Comments Full-scale settling time to within 1/2 LSB of final value 1 LSB change at major carry
12 3 -1 1/2 5 0.5 0.5 0 to VREF 2.5 10 65 15 2 1 VDD 20 1
12 3 -1 1/2 5 0.5 0.5 0 to VREF 2.5 10 67 15 2 1 VDD 20 1
Bits LSB typ LSB max LSB typ mV max % typ % typ V typ V mV Max dB typ ppm/C typ ms typ V min V max k typ A max
Guaranteed 12-bit monotonic VREF range VREF range % of full-scale on DAC1 DAC VREF = 2.5 V
Of VREF measured at the CREF pin TA = 25C
Internal band gap deselected via ADCCON1.6 Two trip points selectable in this range programmed via TPD1-0 in PSMCON, 3 V part only
2.93 3.08 2.5 0 2000 100,000 100 10 1 10 1 -75 -40 -660 -400 10 10 105 0 2000 100,000 100 10 1 10 1 -25 -15 -250 -140 10 5 35
V min V max % max ms min ms max Cycles min Years min A max A typ A max A typ A max A typ A max A typ A max A min A max
DVDD Power Supply Trip Point Accuracy WATCHDOG TIMER (WDT) 4 Timeout Period FLASH/EE MEMORY RELIABILITY CHARACTERISTICS16 Endurance17 Data Retention18 DIGITAL INPUTS Input Leakage Current (Port 0, EA) Logic 1 Input Current (All Digital Inputs), SDATA, SCLOCK Logic 0 Input Current (Ports 1, 2, 3) SDATA, SCLOCK Logic 1 to Logic 0 Transition Current (Ports 2 and 3) RESET
Nine timeout periods selectable in this range
VIN = 0 V or VDD VIN = 0 V or VDD VIN = VDD VIN = VDD VIL = 450 mV VIL = 2 V VIL = 2 V VIN = 0 V VIN = 5 V, 3 V Internal Pull Down VIN = 5 V, 3 V Internal Pull Down
Rev. 0 | Page 4 of 88
ADuC841/ADuC842/ADuC843
Parameter LOGIC INPUTS4 INPUT VOLTAGES All Inputs Except SCLOCK, SDATA, RESET, and XTAL1 VINL, Input Low Voltage VINH, Input High Voltage SDATA VINL, Input Low Voltage VINH, Input High Voltage SCLOCK and RESET Only4 (Schmitt-Triggered Inputs) VT+ VT- VT+ - VT- CRYSTAL OSCILLATOR Logic Inputs, XTAL1 Only VINL, Input Low Voltage VINH, Input High Voltage XTAL1 Input Capacitance XTAL2 Output Capacitance MCU CLOCK RATE DIGITAL OUTPUTS Output High Voltage (VOH) VDD = 5 V VDD = 3 V Unit Test Conditions/Comments
0.8 2.0 0.8 2.0
0.4 2.0 0.8 2.0
V max V min V max V min
1.3 3.0 0.8 1.4 0.3 0.85
0.95 0.25 0.4 1.1 0.3 0.85
V min V max V min V max V min V max
0.8 3.5 18 18 16.78 20 2.4 4
0.4 2.5 18 18 8.38 8.38
V typ V typ pF typ pF typ MHz max MHz max V min V typ V min V typ V max V typ V max V max A max A typ ms typ s typ s typ s typ s typ ms typ ms typ
ADuC842/ADuC843 Only ADuC841 Only VDD = 4.5 V to 5.5 V ISOURCE = 80 A VDD = 2.7 V to 3.3 V ISOURCE = 20 A ISINK = 1.6 mA ISINK = 1.6 mA ISINK = 4 mA ISINK = 8 mA, I2C Enabled
2.4 2.6 Output Low Voltage (VOL) ALE, Ports 0 and 2 Port 3 SCLOCK/SDATA Floating State Leakage Current4 STARTUP TIME At Power-On From Idle Mode From Power-Down Mode Wake-up with INT0 Interrupt Wake-up with SPI/I2C Interrupt Wake-up with External RESET After External RESET in Normal Mode After WDT Reset in Normal Mode 0.4 0.2 0.4 0.4 10 1 500 100 150 150 150 30 3 0.4 0.2 0.4 0.4 10 1 500 100 400 400 400 30 3
At any core CLK
Controlled via WDCON SFR
Rev. 0 | Page 5 of 88
ADuC841/ADuC842/ADuC843
Parameter POWER REQUIREMENTS19, 20 Power Supply Voltages AVDD/DVDD - AGND VDD = 5 V VDD = 3 V Unit Test Conditions/Comments
2.7 3.6 4.75 5.25
V min V max V min V max mA typ mA max mA max mA typ mA max mA max mA typ A typ mA max mA typ A typ A max A typ A typ mA max A max A typ
AVDD/DVDD = 3 V nom AVDD/DVDD = 5 V nom
Power Supply Currents Normal Mode21 DVDD Current4 AVDD Current DVDD Current AVDD Current DVDD Current4 Power Supply Currents Idle Mode21 DVDD Current AVDD Current DVDD Current4 AVDD Current Power Supply Currents Power-Down Mode21 DVDD Current AVDD Current DVDD Current4 DVDD Current4
10 1.7 38 33 1.7 45 4.5 3 12 10 3 28 20 2 3 50 40
4.5 1.7 12 10 1.7 N/A 2.2 2 5 3.5 2 18 10 1 1 22 15
Core CLK = 2.097 MHz Core CLK = 2.097 MHz Core CLK = 16.78MHz/8.38 MHz 5 V/3 V Core CLK = 16.78MHz/8.38 MHz 5 V/3 V Core CLK = 16.78MHz/8.38 MHz 5 V/3 V Core CLK = 20MHz ADuC841 Only Core CLK = 2.097 MHz Core CLK = 2.097 MHz Core CLK = 16.78MHz/8.38 MHz 5 V/3 V Core CLK = 16.78MHz/8.38 MHz 5 V/3 V Core CLK = 16.78MHz/8.38 MHz 5 V/3 V Core CLK = any frequency Oscillator Off / TIMECON.1 = 0 Core CLK = any frequency ADuC841 Only TIMECON.1 = 1 Core CLK = any frequency ADuC842/ADuC843 Only Oscillator On AVDD = DVDD MCLK Divider = 32 MCLK Divider = 2
Typical Additional Power Supply Currents PSM Peripheral ADC4 DAC
See footnotes on the next page.
15 1.0 2.8 150
10 1.0 1.8 130
A typ mA min mA max A typ
Rev. 0 | Page 6 of 88
ADuC841/ADuC842/ADuC843
1 2
Temperature Range -40C to +85C. ADC linearity is guaranteed during normal MicroConverter core operation. 3 ADC LSB size = VREF/212, i.e., for internal VREF = 2.5 V, 1 LSB = 610 V, and for external VREF = 1 V, 1 LSB = 244 V. 4 These numbers are not production tested but are supported by design and/or characterization data on production release. 5 Offset and gain error and offset and gain error match are measured after factory calibration. 6 Based on external ADC system components, the user may need to execute a system calibration to remove additional external channel errors to achieve these specifications. 7 SNR calculation includes distortion and noise components. 8 Channel-to-channel crosstalk is measured on adjacent channels. 9 The temperature monitor gives a measure of the die temperature directly; air temperature can be inferred from this result. 10 DAC linearity is calculated using: Reduced code range of 100 to 4095, 0 V to VREF range. Reduced code range of 100 to 3945, 0 V to VDD range. DAC output load = 10 k and 100 pF. 11 DAC differential nonlinearity specified on 0 V to VREF and 0 V to VDD ranges. 12 DAC specification for output impedance in the unbuffered case depends on DAC code. 13 DAC specifications for ISINK, voltage output settling time, and digital-to-analog glitch energy depend on external buffer implementation in unbuffered mode. DAC in unbuffered mode tested with OP270 external buffer, which has a low input leakage current. 14 Measured with CREF pin decoupled with 0.47 F capacitor to ground. Power-up time for the internal reference is determined by the value of the decoupling capacitor chosen for the CREF pin. 15 When using an external reference device, the internal band gap reference input can be bypassed by setting the ADCCON1.6 bit. 16 Flash/EE memory reliability characteristics apply to both the Flash/EE program memory and the Flash/EE data memory. 17 Endurance is qualified to 100,000 cycles as per JEDEC Std. 22 method A117 and measured at -40C, +25C, and +85C. Typical endurance at 25C is 700,000 cycles. 18 Retention lifetime equivalent at junction temperature (TJ) = 55C as per JEDEC Std. 22 method A117. Retention lifetime based on an activation energy of 0.6 eV derates with junction temperature as shown in Figure 38 in the Flash/EE Memory Reliability section. 19 Power supply current consumption is measured in normal, idle, and power-down modes under the following conditions: Normal Mode: Reset = 0.4 V, digital I/O pins = open circuit, Core Clk changed via CD bits in PLLCON (ADuC842/ADuC843), core executing internal software loop. Idle Mode: Reset = 0.4 V, digital I/O pins = open circuit, Core Clk changed via CD bits in PLLCON (ADuC842/ADuC843), PCON.0 = 1, core execution suspended in idle mode. Power-Down Mode: Reset = 0.4 V, all Port 0 pins = 0.4 V, All other digital I/O and Port 1 pins are open circuit, Core Clk changed via CD bits in PLLCON (ADuC842/ADuC843), PCON.0 = 1, core execution suspended in power-down mode, OSC turned on or off via OSC_PD bit (PLLCON.7) in PLLCON SFR (ADuC842/ADuC843). 20 DVDD power supply current increases typically by 3 mA (3 V operation) and 10 mA (5 V operation) during a Flash/EE memory program or erase cycle. 21 Power supply currents are production tested at 5.25 V and 3.3 V for a 5 V and 3 V part, respectively.
Rev. 0 | Page 7 of 88
ADuC841/ADuC842/ADuC843 ABSOLUTE MAXIMUM RATINGS
Table 2. TA = 25C, unless otherwise noted
Parameter AVDD to DVDD AGND to DGND DVDD to DGND, AVDD to AGND Digital Input Voltage to DGND Digital Output Voltage to DGND VREF to AGND Analog Inputs to AGND Operating Temperature Range, Industrial ADuC841BS,ADuC842BS,ADuC843BS ADuC841BCP, ADuC842BCP, ADuC843BCP Storage Temperature Range Junction Temperature JA Thermal Impedance (ADuC84xBS) JA Thermal Impedance (ADuC84xBCP) Lead Temperature, Soldering Vapor Phase (60 sec) Infrared (15 sec) Rating -0.3 V to +0.3 V -0.3 V to +0.3 V -0.3 V to +7 V -0.3 V to DVDD + 0.3 V -0.3 V to DVDD + 0.3 V -0.3 V to AVDD + 0.3 V -0.3 V to AVDD + 0.3 V -40C to +85C
-65C to +150C 150C 90C/W 52C/W 215C 220C
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
ADuC841/ADuC842/ADuC843
ADC0 ADC1 ... MUX ... ADC6 ADC7 62 kBYTES PROGRAM FLASH/EE INCLUDING USER DOWNLOAD MODE 4 kBYTES DATA FLASH/EE 2 kBYTES USER XRAM BUF 2 x DATA POINTERS 11-BIT STACK POINTER DOWNLOADER DEBUGGER
SINGLE-PIN EMULATOR
12-BIT VOLTAGE OUTPUT DAC DAC CONTROL 12-BIT VOLTAGE OUTPUT DAC 16-BIT - DAC PWM CONTROL 16-BIT - DAC 16-BIT PWM 16-BIT PWM MUX
DAC0
T/H
12-BIT ADC
ADC CONTROL AND CALIBRATION
DAC1
PWM0 PWM1
TEMP SENSOR BAND GAP REFERENCE
256 BYTES USER RAM
T0 16-BIT COUNTER TIMERS T1 T2 T2EX
8052
MCU CORE
WATCHDOG TIMER POWER SUPPLY MONITOR
INT0 TIME INTERVAL COUNTER (WAKE-UP CCT) UART TIMER SYNCHRONOUS SERIAL INTERFACE (I2C AND SPI ) PLL OSC
03260-0-002
CREF
INT1
POR
ASYNCHRONOUS SERIAL PORT (UART)
RESET
XTAL1
SCLOCK
Figure 2. ADuC Block Diagram (Shaded Areas are Features Not Present on the ADuC812), No DACs on ADuC843, PLL on ADuC842/ADuC843 Only.
Rev. 0 | Page 8 of 88
SDATA\MOSI
XTAL2
AVDD
DVDD
DVDD
DVDD
ALE
PSEN
AGND
DGND
DGND
DGND
MISO
RxD
TxD
EA
SS
ADuC841/ADuC842/ADuC843 PIN CONFIGURATIONS AND FUNCTIONAL DESCRIPTIONS
P0.7/AD7 P0.6/AD6 P0.5/AD5 P0.4/AD4 P0.3/AD3 P0.2/AD2 P0.0/AD0 P0.1/AD1
P1.0/ADC0/T2
DGND
DVDD
PSEN
ALE
P0.7/AD7
P0.6/AD6
P0.5/AD5
P0.4/AD4 DVDD
DGND P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
EA
ALE 45
P1.0/ADC0/T2 1 P1.1/ADC1/T2EX 2 P1.2/ADC2 3 P1.3/ADC3 4 AVDD 5 AGND 6 CREF 7 VREF 8 DAC0 9 DAC1 10 P1.4/ADC4 11 P1.5/ADC5/SS 12 P1.6/ADC6 13
56
55
54
53
52
51
50
49
48
47
46
37 36
P2.5/A13/A21 P2.4/A12/A20 DGND DVDD XTAL2 XTAL1 P2.3/A11/A19 P2.2/A10/A18 P2.1/A9/A17 P2.0/A8/A16 SDATA/MOSI
P1.1/ADC1/T2EX P1.2/ADC2 P1.3/ADC3 AVDD AVDD AGND AGND AGND CREF VREF DAC0 DAC1 P1.4/ADC4 P1.5/ADC5/SS
44 43
PIN 1 IDENTIFIER
39 38
P2.7/PWM1/A15/A23 P2.6/PWM0/A14/A22 1 2 3 4 5 6 7 8 9 10 11 12 13 14
EA
52 51 50 49 48 47 46 45 44 43 42 41 40
PSEN
ADuC841/ADuC842/ADuC843 52-LEAD PQFP
TOP VIEW (Not to Scale)
35 34 33 32 31 30 29 28 27
PIN 1 IDENTIFIER
42 41 40 39 38 37 36 35 34 33 32 31 30 29
P2.7/A15/A23 P2.6/A14/A22 P2.5/A13/A21 P2.4/A12/A20 DGND DGND DVDD XTAL2 XTAL1 P2.3/A11/A19 P2.2/A10/A18 P2.1/A9/A17 P2.0/A8/A16 SDATA/MOSI
ADuC841/ADuC842/ADuC843 56-LEAD CSP
TOP VIEW (Not to Scale)
14 15 16 17 18 19 20 21 22 23 24 25 26
P3.0/RXD
P3.1/TXD
P3.3/INT1/MISO/PWM1 DVDD
DGND P3.4/T0/PWMC/PWM0/EXTCLK*
P3.5/T1/CONVST P3.6/WR P3.7/RD
P1.7/ADC7
RESET
P3.2/INT0
SCLOCK
15
16
17
18
19
20
21
22
23
24
25
26 P3.6/WR
27
P3.3/INT1/MISO/PWM1 DVDD
P.7/ADC7
P3.0/RxD
P3.1/TxD
Figure 3. 52-Lead PQPF
*EXTCLK NOT PRESENT ON THE ADuC841
Figure 4. 56-Lead CSP
Table 3. Pin Function Descriptions
Mnemonic DVDD AVDD CREF VREF AGND P1.0-P1.7 ADC0-ADC7 T2 T2EX SS SDATA SCLOCK MOSI MISO DAC0 DAC1 RESET Type P P I/O NC G I I I I I I/O I/O I/O I/O O O I Function Digital Positive Supply Voltage. 3 V or 5 V nominal. Analog Positive Supply Voltage. 3 V or 5 V nominal. Decoupling Input for On-Chip Reference. Connect a 0.47 F capacitor between this pin and AGND. Not connected. This was reference out on the ADuC812; the CREF pin should be used instead. Analog Ground. Ground reference point for the analog circuitry. Port 1 is an 8-bit input port only. Unlike other ports, Port 1 defaults to analog input mode. To configure any of these port pins as a digital input, write a 0 to the port bit. Analog Inputs. Eight single-ended analog inputs. Channel selection is via ADCCON2 SFR. Timer 2 Digital Input. Input to Timer/Counter 2. When enabled, Counter 2 is incremented in response to a 1-to-0 transition of the T2 input. Digital Input. Capture/reload trigger for Counter 2; also functions as an up/down control input for Counter 2. Slave Select Input for the SPI Interface. User Selectable, I2C Compatible, or SPI Data Input/Output Pin. Serial Clock Pin for I2C Compatible or for SPI Serial Interface Clock. SPI Master Output/Slave Input Data I/O Pin for SPI Interface. SPI Master Input/Slave Output Data I/O Pin for SPI Serial Interface. Voltage Output from DAC0. This pin is a no connect on the ADuC843. Voltage Output from DAC1. This pin is a no connect on the ADuC843. Digital Input. A high level on this pin for 24 master clock cycles while the oscillator is running resets the device.
Rev. 0 | Page 9 of 88
03260-0-004
*EXTCLK NOT PRESENT ON THE ADuC841
P3.4/T0/PWMC/PWM0/EXTCLK*
03260-0-003
P3.5/T1/CONVST
P1.6/ADC6
P3.2/INT0
P3.7/RD SCLOCK
RESET
DGND
28
ADuC841/ADuC842/ADuC843
Mnemonic P3.0-P3.7 Type I/O Function Port 3 is a bidirectional port with internal pull-up resistors. Port 3 pins that have 1s written to them are pulled high by the internal pull-up resistors, and in that state can be used as inputs. As inputs, Port 3 pins being pulled externally low source current because of the internal pull-up resistors. Port 3 pins also contain various secondary functions, which are described below. PWM Clock Input. PWM0 Voltage Output. PWM outputs can be configured to use Ports 2.6 and 2.7 or Ports 3.4 and 3.3. PWM1 Voltage Output. See the CFG841/CFG842 register for further information. Receiver Data Input (Asynchronous) or Data Input/Output (Synchronous) of the Serial (UART) Port. Transmitter Data Output (Asynchronous) or Clock Output (Synchronous) of the Serial (UART) Port. Interrupt 0. Programmable edge or level triggered interrupt input; can be programmed to one of two priority levels. This pin can also be used as a gate control input to Timer 0. Interrupt 1. Programmable edge or level triggered interrupt input; can be programmed to one of two priority levels. This pin can also be used as a gate control input to Timer 1. Timer/Counter 0 Input. Timer/Counter 1 Input. Active Low Convert Start Logic Input for the ADC Block when the External Convert Start Function is Enabled. A low-to-high transition on this input puts the track-and-hold into hold mode and starts the conversion. Input for External Clock Signal. Has to be enabled via the CFG842 register. Write Control Signal, Logic Output. Latches the data byte from Port 0 into the external data memory. Read Control Signal, Logic Output. Enables the external data memory to Port 0. Output of the Inverting Oscillator Amplifier. Input to the Inverting Oscillator Amplifier. Digital Ground. Ground reference point for the digital circuitry. Port 2 is a bidirectional port with internal pull-up resistors. Port 2 pins that have 1s written to them are pulled high by the internal pull-up resistors, and in that state can be used as inputs. As inputs, Port 2 pins being pulled externally low source current because of the internal pull-up resistors. Port 2 emits the middle and high-order address bytes during accesses to the external 24-bit external data memory space. Program Store Enable, Logic Output. This pin remains low during internal program execution. PSEN is used to enable serial download mode when pulled low through a resistor on power-up or reset. On reset this pin will momentarily become an input and the status of the pin is sampled. If there is no pulldown resistor in place the pin will go momentarilly high and then user code will execute. If a pull-down resistor is in place, the embedded serial download/debug kernel will execute. Address Latch Enable, Logic Output. This output is used to latch the low byte and page byte for 24-bit address space accesses of the address into external data memory. External Access Enable, Logic Input. When held high, this input enables the device to fetch code from internal program memory locations. The parts do not support external code memory. This pin should not be left floating. Port 0 is an 8-bit open-drain bidirectional I/O port. Port 0 pins that have 1s written to them float, and in that state can be used as high impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external data memory. In this application, it uses strong internal pull-ups when emitting 1s.
PWMC PWM0 PWM1 RxD TxD INT0 INT1 T0 T1 CONVST EXTCLK WR RD XTAL2 XTAL1 DGND P2.0-P2.7 (A8-A15) (A16-A23) PSEN
I O O I/O O I I I I I I O O O I G I/O
O
ALE EA P0.7-P0.0 (A0-A7)
O I I/O
Types: P = Power, G = Ground, I= Input, O = Output., NC = No Connect
Rev. 0 | Page 10 of 88
ADuC841/ADuC842/ADuC843 TERMINOLOGY
ADC SPECIFICATIONS
Integral Nonlinearity The maximum deviation of any code from a straight line passing through the endpoints of the ADC transfer function. The endpoints of the transfer function are zero scale, a point 1/2 LSB below the first code transition, and full scale, a point 1/2 LSB above the last code transition. Differential Nonlinearity The difference between the measured and the ideal 1 LSB change between any two adjacent codes in the ADC. Offset Error The deviation of the first code transition (0000 . . . 000) to (0000 . . . 001) from the ideal, i.e., +1/2 LSB. Gain Error The deviation of the last code transition from the ideal AIN voltage (Full Scale - 1/2 LSB) after the offset error has been adjusted out. Signal-to-(Noise + Distortion) Ratio The measured ratio of signal to (noise + distortion) at the output of the ADC. The signal is the rms amplitude of the fundamental. Noise is the rms sum of all nonfundamental signals up to half the sampling frequency (fS/2), excluding dc. The ratio depends on the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. The theoretical signal-to-(noise + distortion) ratio for an ideal N-bit converter with a sine wave input is given by Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB Thus for a 12-bit converter, this is 74 dB. Total Harmonic Distortion (THD) The ratio of the rms sum of the harmonics to the fundamental.
DAC SPECIFICATIONS
Relative Accuracy Relative accuracy or endpoint linearity is a measure of the maximum deviation from a straight line passing through the endpoints of the DAC transfer function. It is measured after adjusting for zero error and full-scale error. Voltage Output Settling Time The amount of time it takes for the output to settle to a specified level for a full-scale input change. Digital-to-Analog Glitch Impulse The amount of charge injected into the analog output when the inputs change state. It is specified as the area of the glitch in nV-sec.
Rev. 0 | Page 11 of 88
ADuC841/ADuC842/ADuC843 TYPICAL PERFORMANCE CHARACTERISTICS
The typical performance plots presented in this section illustrate typical performance of the ADuC841/ADuC842/ ADuC843 under various operating conditions. Figure 5 and Figure 6 show typical ADC integral nonlinearity (INL) errors from ADC Code 0 to Code 4095 at 5 V and 3 V supplies, respectively. The ADC is using its internal reference (2.5 V) and is operating at a sampling rate of 152 kHz; the typical worst-case errors in both plots are just less than 0.3 LSB. Figure 7 and Figure 8 also show ADC INL at a higher sampling rate of 400 kHz. Figure 9 and Figure 10 show the variation in worst-case positive (WCP) INL and worst-case negative (WCN) INL versus external reference input voltage. Figure 11 and Figure 12 show typical ADC differential nonlinearity (DNL) errors from ADC Code 0 to Code 4095 at 5 V and 3 V supplies, respectively. The ADC is using its internal reference (2.5 V) and is operating at a sampling rate of 152 kHz; the typical worst-case errors in both plots are just less than 0.2 LSB. Figure 13 and Figure 14 show the variation in worstcase positive (WCP) DNL and worst-case negative (WCN) DNL versus external reference input voltage. Figure 15 shows a histogram plot of 10,000 ADC conversion results on a dc input with VDD = 5 V. The plot illustrates an excellent code distribution pointing to the low noise performance of the on-chip precision ADC.
1.0 0.8 0.6 0.4 0.2
LSBs
Figure 16 shows a histogram plot of 10,000 ADC conversion results on a dc input for VDD = 3 V. The plot again illustrates a very tight code distribution of 1 LSB with the majority of codes appearing in one output pin. Figure 17 and Figure 18 show typical FFT plots for the parts. These plots were generated using an external clock input. The ADC is using its internal reference (2.5 V), sampling a full-scale, 10 kHz sine wave test tone input at a sampling rate of 149.79 kHz. The resulting FFTs shown at 5 V and 3 V supplies illustrate an excellent 100 dB noise floor, 71 dB signal-to-noise ratio (SNR), and THD greater than -80 dB. Figure 19 and Figure 20 show typical dynamic performance versus external reference voltages. Again, excellent ac performance can be observed in both plots with some roll-off being observed as VREF falls below 1 V. Figure 21 shows typical dynamic performance versus sampling frequency. SNR levels of 71 dB are obtained across the sampling range of the parts. Figure 22 shows the voltage output of the on-chip temperature sensor versus temperature. Although the initial voltage output at 25C can vary from part to part, the resulting slope of -1. 4 mV/C is constant across all parts.
1.0
AVDD / DVDD = 5V fS = 152kHz
AVDD /DVDD = 3V 0.8 0.6 0.4 0.2
fS = 152kHz
0 -0.2 -0.4 -0.6 -0.8
03260-0-005
LSBs
0 -0.2 -0.4 -0.6 -0.8 -1.0 0 511 1023 1535 2047 2559 ADC CODES 3071 3583 4095
03260-0-006
-1.0 0 511 1023 1535 2047 2559 ADC CODES 3071 3583 4095
Figure 5. Typical INL Error, VDD = 5 V, fs = 152 kHz
Figure 6. Typical INL Error, VDD = 3 V, fs = 152 kHz
Rev. 0 | Page 12 of 88
ADuC841/ADuC842/ADuC843
1.0 0.8 0.6 0.4 0.2
LSBs
0.2 0 -0.2 -0.4 WCN INL 0.2 0 -0.2 -0.4 -0.6 -0.8 0.5 1.5 2.5 1.0 2.0 EXTERNAL REFERENCE (V) 3.0
03260-0-008
0.8
0.8 AVDD/DVDD = 3V
AVDD/DVDD = 5V fS = 400kHz CD = 4
0.6 0.4
fS = 152kHz
WCP INL
0.6 0.4
0 -0.2 -0.4 -0.6 -0.8
03260-0-098
-0.6 -0.8
-1.0 0 511 1023 1535 2047 2559 ADC CODES 3071 3583 4095
Figure 7. Typical INL Error, VDD = 5 V, fS = 400 kHz
1.0 0.8 0.6 0.4 0.2
LSBs
1.0
Figure 10. Typical Worst-Case INL Error vs. VREF, VDD = 3 V
AVDD/DVDD = 3V fS = 400kHz CD = 4
AV DD /DVDD = 5V 0.8 0.6 0.4 0.2
fS = 152kHz
0 -0.2 -0.4 -0.6 -0.8
03260-0-099
LSBs
0 -0.2 -0.4 -0.6 -0.8 -1.0 0 511 1023 1535 2047 2559 ADC CODES 3071 3583 4095
03260-0-009 03260-0-010
-1.0 0 511 1023 1535 2047 2559 ADC CODES 3071 3583 4095
Figure 8. Typical INL Error, VDD = 3 V, fS = 400 kHz
1.2
Figure 11. Typical DNL Error, VDD = 5 V
0.6
1.0 AV DD /DVDD = 3V 0.8
AVDD/DVDD = 5V
1.0 0.8
fS = 152kHz
0.4
fS = 152kHz
0.6
WCP INL 0.4 0 0.2 0 -0.2 -0.4 -0.6 0.5 1.0 1.5 2.0 2.5 EXTERNAL REFERENCE (V) 5.0 -0.6 WCN INL -0.4 -0.2
WCN-INL (LSBs)
WCP-INL (LSBs)
0.6
0.2
0.4 0.2
LSBs
0 -0.2 -0.4 -0.6 -0.8
03260-0-007
-1.0 0 511 1023 1535 2047 2559 ADC CODES 3071 3583 4095
Figure 9. Typical Worst-Case INL Error vs. VREF, VDD = 5 V
Figure 12. Typical DNL Error, VDD = 3 V
Rev. 0 | Page 13 of 88
WCN-INL (LSBs)
WCP-INL (LSBs)
ADuC841/ADuC842/ADuC843
0.6 AVDD /DVDD = 5V fS = 152kHz 0.4 0.4
8000 7000
0.6
10000 9000
WCN-DNL (LSBs)
WCP-DNL (LSBs)
0.2
WCP DNL
0.2
OCCURRENCE
03260-0-011
6000 5000 4000 3000
0
0
-0.2 WCN DNL -0.4
-0.2
-0.4
2000 1000
-0.6 0.5 1.0 1.5 2.0 2.5 EXTERNAL REFERENCE (V) 5.0
-0.6
0 817 818 819 CODE 820 821
Figure 13. Typical Worst-Case DNL Error vs. VREF, VDD = 5 V
Figure 16. Code Histogram Plot, VDD = 3 V
0.7
20 0 -20 AVDD/DVDD = 5V fS = 152kHz fIN = 9.910kHz SNR = 71.3dB THD = -88.0dB ENOB = 11.6
0.7 0.5 0.3
AVDD/DVDD = 3V fS = 152kHz
0.5 0.3 0.1 -0.1
WCP DNL
0.1 -0.1 WCN DNL -0.3 -0.5 -0.7 0.5 1.0 1.5 2.0 2.5 EXTERNAL REFERENCE (V) 3.0
WCN-DNL (LSBs)
WCP-DNL (LSBs)
-40 -60
dBs
-80 -100 -120
-0.3 -0.5
-140 -160 0 10 20 30 40 FREQUENCY (kHz) 50 60 70
03260-0-015
03260-0-016
-0.7
Figure 14. Typical Worst-Case DNL Error vs. VREF, VDD = 3 V
03260-0-012
Figure 17. Dynamic Performance at VDD = 5 V
10000
20 0 AVDD/DVDD = 3V fS = 149.79kHz fIN = 9.910kHz SNR = 71.0dB THD = -83.0dB ENOB = 11.5
8000
-20 -40
OCCURRENCE
6000
-60
dBs
-80 -100
4000
2000
-120 -140
03260-0-013
0 817 818 819 CODE 820 821
-160 0 10 20 30 40 FREQUENCY (kHz) 50 60 70
Figure 15. Code Histogram Plot, VDD = 5 V
Figure 18. Dynamic Performance at VDD = 3 V
Rev. 0 | Page 14 of 88
03260-0-014
ADuC841/ADuC842/ADuC843
80 AVDD /DVDD = 5V fS = 152kHz SNR 70 -80 -70
80 78 AVDD /DVDD = 5V
75
-75
76 74
SNR (dBs)
THD (dBs)
65 THD 60
-85
SNR (dBs)
72 70 68 66 64 62
119.050 172.620 199.410 145.830 226.190 300.000 350.000
-90
55
-95
03260-0-017
0.5
1.0 1.5 2.0 2.5 EXTERNAL REFERENCE (V)
5.0
Figure 19. Typical Dynamic Performance vs. VREF, VDD = 5 V
FREQUENCY (kHz)
Figure 21. Typical Dynamic Performance vs. Sampling Frequency
80 AVDD /DVDD = 3V -70
0.9 0.8 0.7
fS = 152kHz
75 SNR 70 -80 -75
AVDD/DVDD = 3V SLOPE = -1.4mV/C
SNR (dBs)
THD (dBs)
VOLTAGE
THD 65 -85
0.6 0.5 0.4
60
-90
55
-95
0.3
03260-0-018
400.000
65.476
92.262
50 0.5 1.0 2.0 1.5 2.5 EXTERNAL REFERENCE (V) 3.0
-100
0.2 -40 25 TEMPERATURE (C) 85
Figure 20. Typical Dynamic Performance vs. VREF, VDD = 3 V
Figure 22. Typical Temperature Sensor Output vs. Temperature
GENERAL DESCRIPTION (continued)
The parts also incorporate additional analog functionality with two 12-bit DACs, power supply monitor, and a band gap reference. On-chip digital peripherals include two 16-bit -. DACs, a dual output 16-bit PWM, a watchdog timer, a time interval counter, three timers/counters, and three serial I/O ports (SPI, I2C, and UART). On the ADuC812 and the ADuC832, the I2C and SPI interfaces share some of the same pins. For backwards compatibility, this is also the case for the ADuC841/ADuC842/ADuC843. However, there is also the option to allow SPI operate separately on P3.3, P3.4, and P3.5, while I2C uses the standard pins. The I2C interface has also been enhanced to offer repeated start, general call, and quad addressing. On-chip factory firmware supports in-circuit serial download and debug modes (via UART) as well as single-pin emulation mode via the EA pin. A functional block diagram of the parts is shown on the first page.
Rev. 0 | Page 15 of 88
03260-0-100
03260-0-019
50
-100
60
ADuC841/ADuC842/ADuC843 FUNCTIONAL DESCRIPTION
8052 INSTRUCTION SET
Table 4 documents the number of clock cycles required for each instruction. Most instructions are executed in one or two clock cycles, resulting in a 16 MIPS peak performance when operating at PLLCON = 00H on the ADuC842/ADuC843. On the ADuC841, 20 MIPS peak performance is possible with a 20 MHz external crystal. Table 4. Instructions
Mnemonic Arithmetic ADD A,Rn ADD A,@Ri ADD A,dir ADD A,#data ADDC A,Rn ADDC A,@Ri ADDC A,dir ADD A,#data SUBB A,Rn SUBB A,@Ri SUBB A,dir SUBB A,#data INC A INC Rn INC @Ri INC dir INC DPTR DEC A DEC Rn DEC @Ri DEC dir MUL AB DIV AB DA A Logic ANL A,Rn ANL A,@Ri ANL A,dir ANL A,#data ANL dir,A ANL dir,#data ORL A,Rn ORL A,@Ri ORL A,dir ORL A,#data ORL dir,A ORL dir,#data XRL A,Rn XRL A,@Ri XRL A,#data XRL dir,A Description Add register to A Add indirect memory to A Add direct byte to A Add immediate to A Add register to A with carry Add indirect memory to A with carry Add direct byte to A with carry Add immediate to A with carry Subtract register from A with borrow Subtract indirect memory from A with borrow Subtract direct from A with borrow Subtract immediate from A with borrow Increment A Increment register Increment indirect memory Increment direct byte Increment data pointer Decrement A Decrement register Decrement indirect memory Decrement direct byte Multiply A by B Divide A by B Decimal adjust A AND register to A AND indirect memory to A AND direct byte to A AND immediate to A AND A to direct byte AND immediate data to direct byte OR register to A OR indirect memory to A OR direct byte to A OR immediate to A OR A to direct byte OR immediate data to direct byte Exclusive-OR register to A Exclusive-OR indirect memory to A Exclusive-OR immediate to A Exclusive-OR A to direct byte
Rev. 0 | Page 16 of 88
Bytes 1 1 2 2 1 1 2 2 1 1 2 2 1 1 1 2 1 1 1 1 2 1 1 1 1 1 2 2 2 3 1 1 2 2 2 3 1 2 2 2
Cycles 1 2 2 2 1 2 2 2 1 2 2 2 1 1 2 2 3 1 1 2 2 9 9 2 1 2 2 2 2 3 1 2 2 2 2 3 1 2 2 2
ADuC841/ADuC842/ADuC843
Mnemonic XRL A,dir XRL dir,#data CLR A CPL A SWAP A RL A RLC A RR A RRC A Data Transfer MOV A,Rn MOV A,@Ri MOV Rn,A MOV @Ri,A MOV A,dir MOV A,#data MOV Rn,#data MOV dir,A MOV Rn, dir MOV dir, Rn MOV @Ri,#data MOV dir,@Ri MOV @Ri,dir MOV dir,dir MOV dir,#data MOV DPTR,#data MOVC A,@A+DPTR MOVC A,@A+PC MOVX A,@Ri MOVX A,@DPTR MOVX @Ri,A MOVX @DPTR,A PUSH dir POP dir XCH A,Rn XCH A,@Ri XCHD A,@Ri XCH A,dir Boolean CLR C CLR bit SETB C SETB bit CPL C CPL bit ANL C,bit ANL C,/bit ORL C,bit ORL C,/bit MOV C,bit MOV bit,C Description Exclusive-OR indirect memory to A Exclusive-OR immediate data to direct Clear A Complement A Swap nibbles of A Rotate A left Rotate A left through carry Rotate A right Rotate A right through carry Move register to A Move indirect memory to A Move A to register Move A to indirect memory Move direct byte to A Move immediate to A Move register to immediate Move A to direct byte Move register to direct byte Move direct to register Move immediate to indirect memory Move indirect to direct memory Move direct to indirect memory Move direct byte to direct byte Move immediate to direct byte Move immediate to data pointer Move code byte relative DPTR to A Move code byte relative PC to A Move external (A8) data to A Move external (A16) data to A Move A to external data (A8) Move A to external data (A16) Push direct byte onto stack Pop direct byte from stack Exchange A and register Exchange A and indirect memory Exchange A and indirect memory nibble Exchange A and direct byte Clear carry Clear direct bit Set carry Set direct bit Complement carry Complement direct bit AND direct bit and carry AND direct bit inverse to carry OR direct bit and carry OR direct bit inverse to carry Move direct bit to carry Move carry to direct bit Bytes 2 3 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 3 3 3 1 1 1 1 1 1 2 2 1 1 1 2 1 2 1 2 1 2 2 2 2 2 2 2 Cycles 2 3 1 1 1 1 1 1 1 1 2 1 2 2 2 2 2 2 2 2 2 2 3 3 3 4 4 4 4 4 4 2 2 1 2 2 2 1 2 1 2 1 2 2 2 2 2 2 2
Rev. 0 | Page 17 of 88
ADuC841/ADuC842/ADuC843
Mnemonic Branching JMP @A+DPTR RET RETI ACALL addr11 AJMP addr11 SJMP rel JC rel JNC rel JZ rel JNZ rel DJNZ Rn,rel LJMP LCALL addr16 JB bit,rel JNB bit,rel JBC bit,rel CJNE A,dir,rel CJNE A,#data,rel CJNE Rn,#data,rel CJNE @Ri,#data,rel DJNZ dir,rel Miscellaneous NOP Description Jump indirect relative to DPTR Return from subroutine Return from interrupt Absolute jump to subroutine Absolute jump unconditional Short jump (relative address) Jump on carry equal to 1 Jump on carry equal to 0 Jump on accumulator = 0 Jump on accumulator not equal to 0 Decrement register, JNZ relative Long jump unconditional Long jump to subroutine Jump on direct bit = 1 Jump on direct bit = 0 Jump on direct bit = 1 and clear Compare A, direct JNE relative Compare A, immediate JNE relative Compare register, immediate JNE relative Compare indirect, immediate JNE relative Decrement direct byte, JNZ relative No operation Bytes 1 1 1 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 1 Cycles 3 4 4 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 1
1. One cycle is one clock. 2. Cycles of MOVX instructions are four cycles when they have 0 wait state. Cycles of MOVX instructions are 4 + n cycles when they have n wait states. 3. Cycles of LCALL instruction are three cycles when the LCALL instruction comes from interrupt.
OTHER SINGLE-CYCLE CORE FEATURES
Timer Operation
Timers on a standard 8052 increment by 1 with each machine cycle. On the ADuC841/ADuC842/ADuC843, one machine cycle is equal to one clock cycle; therefore the timers increment at the same rate as the core clock. External Memory Access There is no support for external program memory access on the parts. When accessing external RAM, the EWAIT register may need to be programmed to give extra machine cycles to MOVX commands. This is to account for differing external RAM access speeds. EWAIT SFR SFR Address Power-On Default Bit Addressable 9FH 00H No
ALE
The output on the ALE pin on a standard 8052 part is a clock at 1/6th of the core operating frequency. On the ADuC841/ ADuC842/ADuC843 the ALE pin operates as follows. For a single machine cycle instruction,ALE is high for the first half of the machine cycle and low for the second half. The ALE output is at the core operating frequency. For a two or more machine cycle instruction, ALE is high for the first half of the first machine cycle and low for the rest of the machine cycles.
This special function register (SFR) is programmed with the number of wait states for a MOVX instruction. This value can range from 0H to 7H.
Rev. 0 | Page 18 of 88
ADuC841/ADuC842/ADuC843
MEMORY ORGANIZATION
The ADuC841/ADuC842/ADuC843 each contain four different memory blocks: * * * * Up to 62 kBytes of on-chip Flash/EE program memory 4 kBytes of on-chip Flash/EE data memory 256 bytes of general-purpose RAM 2 kBytes of internal XRAM The lower 128 bytes of internal data memory are mapped as shown in Figure 23. The lowest 32 bytes are grouped into four banks of eight registers addressed as R0 to R7. The next 16 bytes (128 bits), locations 20H to 2FH above the register banks, form a block of directly addressable bit locations at Bit Addresses 00H to 7FH. The stack can be located anywhere in the internal memory address space, and the stack depth can be expanded up to 2048 bytes. Reset initializes the stack pointer to location 07H and increments it once before loading the stack to start from location 08H, which is also the first register (R0) of register bank 1. Thus, if the user needs to use more than one register bank, the stack pointer should be initialized to an area of RAM not used for data storage.
7FH GENERAL-PURPOSE AREA 30H 2FH BANKS SELECTED VIA BITS IN PSW 11 18H 17H 10 10H 0FH 01 08H 00 00H
03260-0-021
Flash/EE Program Memory
The parts provide up to 62 kBytes of Flash/EE program memory to run user code. The user can run code from this internal memory only. Unlike the ADuC812, where code execution can overflow from the internal code space to external code space once the PC becomes greater than 1FFFH, the parts do not support the roll-over from F7FFH in internal code space to F800H in external code space. Instead, the 2048 bytes between F800H and FFFFH appear as NOP instructions to user code. This internal code space can be downloaded via the UART serial port while the device is in-circuit. 56 kBytes of the program memory can be reprogrammed during run time; thus the code space can be upgraded in the field by using a user defined protocol, or it can be used as a data memory. This is discussed in more detail in the Flash/EE Memory section. For the 32 kBytes memory model, the top 8 kBytes function as the ULOAD space; this is explained in the Flash/EE Memory section.
BIT-ADDRESSABLE (BIT ADDRESSES) 20H 1FH
FOUR BANKS OF EIGHT REGISTERS R0 TO R7 RESET VALUE OF STACK POINTER
Flash/EE Data Memory
4 kBytes of Flash/EE data memory are available to the user and can be accessed indirectly via a group of control registers mapped into the special function register (SFR) area. Access to the Flash/EE data memory is discussed in detail in the Flash/EE Memory section.
07H
Figure 23. Lower 128 Bytes of Internal Data Memory
The parts contain 2048 bytes of internal XRAM, 1792 bytes of which can be configured to an extended 11-bit stack pointer. By default, the stack operates exactly like an 8052 in that it rolls over from FFH to 00H in the general-purpose RAM. On the parts, however, it is possible (by setting CFG841.7 or CFG842.7) to enable the 11-bit extended stack pointer. In this case, the stack rolls over from FFH in RAM to 0100H in XRAM. The 11-bit stack pointer is visible in the SP and SPH SFRs. The SP SFR is located at 81H as with a standard 8052. The SPH SFR is located at B7H. The 3 LSBs of this SFR contain the 3 extra bits necessary to extend the 8-bit stack pointer into an 11-bit stack pointer.
General-Purpose RAM
The general-purpose RAM is divided into two separate memories: the upper and the lower 128 bytes of RAM. The lower 128 bytes of RAM can be accessed through direct or indirect addressing. The upper 128 bytes of RAM can be accessed only through indirect addressing because it shares the same address space as the SFR space, which can be accessed only through direct addressing.
Rev. 0 | Page 19 of 88
ADuC841/ADuC842/ADuC843
07FFH
FFFFFFH FFFFFFH
UPPER 1792 BYTES OF ON-CHIP XRAM (DATA + STACK FOR EXSP = 1, DATA ONLY FOR EXSP = 0) CFG841.7 = 0 CFG842.7 = 0 CFG841.7 = 1 CFG842.7 = 1
EXTERNAL DATA MEMORY SPACE (24-BIT ADDRESS SPACE)
EXTERNAL DATA MEMORY SPACE (24-BIT ADDRESS SPACE)
100H FFH
03260-0-022
000800H 0007FFH
000000H CFG841.0 = 0 CFG842.0 = 0
000000H
00H
00H
CFG841.0 = 1 CFG842.0 = 0
Figure 24. Extended Stack Pointer Operation Figure 25. Internal and External XRAM
External Data Memory (External XRAM)
Just like a standard 8051 compatible core, the ADuC841/ ADuC842/ADuC843 can access external data memory by using a MOVX instruction. The MOVX instruction automatically outputs the various control strobes required to access the data memory. The parts, however, can access up to 16 MBytes of external data memory. This is an enhancement of the 64 kBytes of external data memory space available on a standard 8051 compatible core. The external data memory is discussed in more detail in the Hardware Design Considerations section.
SPECIAL FUNCTION REGISTERS (SFRS)
The SFR space is mapped into the upper 128 bytes of internal data memory space and is accessed by direct addressing only. It provides an interface between the CPU and all on-chip peripherals. A block diagram showing the programming model of the parts via the SFR area is shown in Figure 26. All registers, except the program counter (PC) and the four general-purpose register banks, reside in the SFR area. The SFR registers include control, configuration, and data registers, which provide an interface between the CPU and all on-chip peripherals.
4-kBYTE ELECTRICALLY REPROGRAMMABLE NONVOLATILE FLASH/EE DATA MEMORY
Internal XRAM
The parts contain 2 kBytes of on-chip data memory. This memory, although on-chip, is also accessed via the MOVX instruction. The 2 kBytes of internal XRAM are mapped into the bottom 2 kBytes of the external address space if the CFG841/CFG842 bit is set. Otherwise, access to the external data memory occurs just like a standard 8051. When using the internal XRAM, Ports 0 and 2 are free to be used as generalpurpose I/O.
62-kBYTE ELECTRICALLY REPROGRAMMABLE NONVOLATILE FLASH/EE PROGRAM MEMORY
8051 COMPATIBLE CORE
128-BYTE SPECIAL FUNCTION REGISTER AREA
8-CHANNEL 12-BIT ADC
2304 BYTES RAM
Figure 26. Programming Model
Rev. 0 | Page 20 of 88
03260-0-024
OTHER ON-CHIP PERIPHERALS TEMPERATURE SENSOR 2 x 12-BIT DACs SERIAL I/O WDT PSM TIC PWM
03260-0-023
256 BYTES OF ON-CHIP DATA RAM (DATA + STACK)
LOWER 256 BYTES OF ON-CHIP XRAM (DATA ONLY)
2 kBYTES ON-CHIP XRAM
ADuC841/ADuC842/ADuC843
ACCUMULATOR SFR (ACC)
ACC is the accumulator register and is used for math operations including addition, subtraction, integer multiplication and division, and Boolean bit manipulations. The mnemonics for accumulator-specific instructions refer to the accumulator as A.
Program Status Word (PSW)
The PSW SFR contains several bits reflecting the current status of the CPU, as detailed in Table 5. SFR Address Power-On Default Bit Addressable D0H 00H Yes
B SFR (B)
The B register is used with the ACC for multiplication and division operations. For other instructions, it can be treated as a general-purpose scratchpad register.
Table 5. PSW SFR Bit Designations
Bit 7 6 5 4 3 Name CY AC F0 RS1 RS0 Description Carry Flag. Auxiliary Carry Flag. General-Purpose Flag. Register Bank Select Bits. Selected Bank RS0 RS1 0 0 0 1 1 0 2 0 1 3 1 1 Overflow Flag. General-Purpose Flag. Parity Bit.
Stack Pointer (SP and SPH)
The SP SFR is the stack pointer and is used to hold an internal RAM address that is called the top of the stack. The SP register is incremented before data is stored during PUSH and CALL executions. While the stack may reside anywhere in on-chip RAM, the SP register is initialized to 07H after a reset, which causes the stack to begin at location 08H. As mentioned earlier, the parts offer an extended 11-bit stack pointer. The 3 extra bits used to make up the 11-bit stack pointer are the 3 LSBs of the SPH byte located at B7H.
Data Pointer (DPTR)
The data pointer is made up of three 8-bit registers named DPP (page byte), DPH (high byte), and DPL (low byte). These are used to provide memory addresses for internal and external code access and for external data access. They may be manipulated as a 16-bit register (DPTR = DPH, DPL), although INC DPTR instructions automatically carry over to DPP, or as three independent 8-bit registers (DPP, DPH, DPL). The parts support dual data pointers. Refer to the Dual Data Pointer section.
2 1 0
OV F1 P
Power Control SFR (PCON)
The PCON SFR contains bits for power-saving options and general-purpose status flags, as shown in Table 6. SFR Address Power-On Default Bit Addressable 87H 00H No
Table 6. PCON SFR Bit Designations
Bit No. 7 6 5 4 3 2 1 0 Name SMOD SERIPD INT0PD ALEOFF GF1 GF0 PD IDL Description Double UART Baud Rate. I2C/SPI Power-Down Interrupt Enable. INT0 Power-Down Interrupt Enable. Disable ALE Output. General-Purpose Flag Bit. General-Purpose Flag Bit. Power-Down Mode Enable. Idle Mode Enable.
Rev. 0 | Page 21 of 88
ADuC841/ADuC842/ADuC843
SPECIAL FUNCTION REGISTER BANKS
All registers except the program counter and the four generalpurpose register banks reside in the special function register (SFR) area. The SFR registers include control, configuration, and data registers, which provide an interface between the CPU and other on-chip peripherals. Figure 27 shows a full SFR memory map and SFR contents on reset. Unoccupied SFR locations are shown dark-shaded in the figure (NOT USED). Unoccupied locations in the SFR address space are not
SPICON1
F8H
implemented, i.e., no register exists at this location. If an unoccupied location is read, an unspecified value is returned. SFR locations reserved for on-chip testing are shown lighter shaded (RESERVED) and should not be accessed by user software. Sixteen of the SFR locations are also bit addressable and denoted by 1 in Figure 27, i.e., the bit addressable SFRs are those whose address ends in 0H or 8H.
ISPI
FFH
WCOL
0 FEH
SPE
SPIM
0 FCH
CPOL
CPHA
SPR1
SPR0
0
0 FDH
0 FBH
0 FAH
1 F9H
0 F8H
BITS
DAC0L
F9H 00H
DAC0H
FAH 00H
DAC1L
FBH 00H
DAC1H
FCH 00H
DACCON
FDH 04H
RESERVED RESERVED
04H
F7H
0 F6H
0 F5H
0 F4H
0 F3H
0 F2H
0 F1H
0 F0H
0
BITS
F0H
B1
00H
ADCOFSL3 ADCOFSH3 ADCGAINL3 ADCGAINH3 ADCCON3
F1H 00H F2H 20H F3H 00H F4H 00H F5H 00H
RESERVED
SPIDAT
F7H 00H
I2CSI/MDO I2CGC/MDE I2C1O1MCO I2C1O0/MDI
I2CM
I2CRS
I2CTX
I2CI
0
EFH
0 EEH
0 EDH
0 ECH
0 EBH
0 EAH
0 E9H
0 E8H
BITS
I2CCON1
E8H 00H
RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED
ADCCON1
EFH 40H
E7H
0 E6H
0 E5H
0 E4H
0 E3H
0 E2H
0 E1H
0 E0H
0
BITS
ACC1
E0H 00H
1
RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED
ADCI
DFH
DMA
CCONV SCONV
0 DCH
CS3
CS2
0 DAH
CS1
0 D9H
CS0
0 D8H
ADCCON2 ADCDATAL ADCDATAH
0
0 DEH
0 DDH
0 DBH
BITS
D8H 00H D9H 00H DAH 00H
RESERVED RESERVED RESERVED RESERVED
PSMCON
DFH DEH
CY
D7H
AC
0 D6H
F0
0 D5H
RS1
0 D4H
RS0
0 D3H
OV
0 D2H
FI
0 D1H
P
0 D0H 0
BITS
PSW 1
D0H 00H
RESERVED
DMAL
D2H 00H
DMAH
D3H 00H
DMAP
D4H 00H
RESERVED RESERVED
PLLCON
D7H 53H
TF2
CFH
EXF2
0 CEH
RCLK
TCLK
EXEN2
TR2
CNT2
0 C9H
CAP2
0
0 CDH
0 CCH
0 CBH
0 CAH
0 C8H
BITS
T2CON1
C8H 00H
RESERVED
RCAP2L
CAH 00H
RCAP2H
CBH 00H
TL2
CCH 00H
TH2
CDH 00H
RESERVED RESERVED
PRE3
C7H
PRE2
PRE1
PRE0
WDIR
WDS
WDE
WDWR
0
BITS
WDCON1 RESERVED
C0H 10H
CHIPID
C2H XXH
RESERVED RESERVED RESERVED
EDARL
C6H 00H
EDARH
C7H 00H
0 C6H
0 C5H
0 C4H
1 C3H
0 C2H
0 C1H
0 C0H
PSI
BFH
PADC
0 BEH
PT2
PS
0 BCH
PT1
0 BBH
PX1
0 BAH
PT0
0 B9H
PX0
0 B8H 0
0 BDH
BITS
IP1
B8H 00H
ECON
B9H 00H
RESERVED RESERVED
EDATA1
BCH 00H
EDATA2
BDH 00H
EDATA3
BEH 00H
EDATA4
BFH 00H
RD
B7H
WR
1 B6H
T1
1 B5H
T0
1 B4H
INT1
1 B3H
INT0
1 B2H
TxD
RxD
1 B0H 1
1 B1H
BITS
P31
B0H
PWM0L
PWM0H
PWM1L
PWM1H
00H
NOT USED
NOT USED
SPH
B7H 00H
FFH B1H
00H B2H
00H B3H
00H B4H
EA
AFH
EADC
0 AEH
ET2
ES
0 ACH
ET1
0 ABH
EX1
0 AAH
ET0
0 A9H
EX0
0 A8H 0
0 ADH
BITS
IE1
A8H 00H
IEIP2
A9H A0H
PWMCON CFG841/ RESERVED RESERVED RESERVED RESERVED CFG842
AEH 00H AFH 00H
A7H
1 A6H
1 A5H
1 A4H
1 A3H
1 A2H
1 A1H
1 A0H
1
BITS
P21
A0H FFH
TIMECON HTHSEC
A1H 00H A2H
SEC
00H
MIN
A4H 00H
HOUR
A5H 00H
INTVAL
A6H
DPCON
00H
00H A3H
00H A7H
SM0
9FH
SM1
0 9EH
SM2
0 9DH
REN
0 9CH
TB8
0 9BH
RB8
0 9AH
TI
0 99H
RI
0 98H 0
BITS
SCON1
98H 00H
SBUF
99H 00H
I2CDAT
9AH
I2CADD
55H
NOT USED
T3FD
9DH
T3CON
00H
NOT USED
00H 9BH
00H 9EH
T2EX
97H 1 96H 1 95H 1 94H 1 93H 1 92H 1 91H
T2
1
1 90H
BITS
P11, 2
90H FFH
I2CADD1
91H 7FH
I2CADD2 I2CADD3
92H 7FH 93H 7FH
NOT USED
NOT USED
NOT USED
NOT USED
TF1
8FH
TR1
0 8EH
TF0
0 8DH
TR0
0 8CH
IE1
0 8BH
IT1
0 8AH
IE0
0 89H
IT0
0 88H 0
BITS
TCON1
88H 00H
TMOD
89H 00H
TL0
8AH 00H
TL1
8BH 00H
TH0
8CH 00H
TH1
8DH 00H
RESERVED RESERVED
87H
1 86H
1 85H
1 84H
1 83H
1 82H
1 81H
1 80H
1
BITS
P01
80H FFH
SP
81H 07H
DPL
82H 00H
DPH
83H 00H
DPP
84H 00H
RESERVED RESERVED
PCON
87H 00H
SFR MAP KEY:
THESE BITS ARE CONTAINED IN THIS BYTE.
MNEMONIC SFR ADDRESS
DEFAULT VALUE NOTES
2 THE 1 SFRs
IE0
89H
IT0
0 88H 0
TCON
88H 00H
MNEMONIC DEFAULT VALUE SFR ADDRESS
03260-0-025
WHOSE ADDRESS ENDS IN 0H OR 8H ARE BIT ADDRESSABLE. PRIMARY FUNCTION OF PORT1 IS AS AN ANALOG INPUT PORT; THEREFORE, TO ENABLE THE DIGITAL SECONDARY FUNCTIONS ON THESE PORT PINS, WRITE A 0 TO THE CORRESPONDING PORT 1 SFR BIT. 3 CALIBRATION COEFFICIENTS ARE PRECONFIGURED ON POWER-UP TO FACTORY CALIBRATED VALUES.
Figure 27. Special Function Register Locations and Reset Values
Rev. 0 | Page 22 of 88
ADuC841/ADuC842/ADuC843
ADC CIRCUIT INFORMATION
General Overview
The ADC conversion block incorporates a fast, 8-channel, 12-bit, single-supply ADC. This block provides the user with multichannel mux, track-and-hold, on-chip reference, calibration features, and ADC. All components in this block are easily configured via a 3-register SFR interface. The ADC converter consists of a conventional successive approximation converter based around a capacitor DAC. The converter accepts an analog input range of 0 V to VREF. A high precision, 15 ppm, low drift, factory calibrated 2.5 V reference is provided on-chip. An external reference can be connected as described in the Voltage Reference Connections section. This external reference can be in the range 1 V to AVDD. Single-step or continuous conversion modes can be initiated in software or alternatively by applying a convert signal to an external pin. Timer 2 can also be configured to generate a repetitive trigger for ADC conversions. The ADC may be configured to operate in a DMA mode whereby the ADC block continuously converts and captures samples to an external RAM space without any interaction from the MCU core. This automatic capture facility can extend through a 16 MByte external data memory space. The ADuC841/ADuC842/ADuC843 are shipped with factory programmed calibration coefficients that are automatically downloaded to the ADC on power-up, ensuring optimum ADC performance. The ADC core contains internal offset and gain calibration registers that can be hardware calibrated to minimize system errors. A voltage output from an on-chip band gap reference proportional to absolute temperature can also be routed through the front end ADC multiplexer (effectively a 9th ADC channel input), facilitating a temperature sensor implementation.
ADC Transfer Function
The analog input range for the ADC is 0 V to VREF. For this range, the designed code transitions occur midway between successive integer LSB values, i.e., 0.5 LSB, 1.5 LSB, 2.5 LSB . . . FS -1.5 LSB. The output coding is straight binary with 1 LSB = FS/4096 or 2.5 V/4096 = 0.61 mV when VREF = 2.5 V. The ideal input/output transfer characteristic for the 0 V to VREF range is shown in Figure 28.
OUTPUT CODE 111...111 111...110 111...101 111...100
1LSB =
FS 4096
000...011
000...010
03260-0-026
000...001 000...000 0V 1LSB
+FS
Figure 28. ADC Transfer Function
Typical Operation
Once configured via the ADCCON 1-3 SFRs, the ADC converts the analog input and provides an ADC 12-bit result word in the ADCDATAH/L SFRs. The top 4 bits of the ADCDATAH SFR are written with the channel selection bits to identify the channel result. The format of the ADC 12-bit result word is shown in Figure 29.
ADCDATAH SFR CH-ID TOP 4 BITS HIGH 4 BITS OF ADC RESULT WORD ADCDATAL SFR LOW 8 BITS OF THE ADC RESULT WORD
03260-0-027
Figure 29. ADC Result Word Format
Rev. 0 | Page 23 of 88
ADuC841/ADuC842/ADuC843
ADCCON1--(ADC Control SFR 1)
The ADCCON1 register controls conversion and acquisition times, hardware conversion modes, and power-down modes as detailed below. SFR Address SFR Power-On Default Bit Addressable EFH 40H No
Table 7. ADCCON1 SFR Bit Designations
Bit No. 7 Name MD1 Description The mode bit selects the active operating mode of the ADC. Set by the user to power up the ADC. Cleared by the user to power down the ADC. Set by the user to select an external reference. Cleared by the user to use the internal reference. The ADC clock divide bits (CK1, CK0) select the divide ratio for the PLL master clock (ADuC842/ADuC843) or the external crystal (ADuC841) used to generate the ADC clock. To ensure correct ADC operation, the divider ratio must be chosen to reduce the ADC clock to 8.38 MHz or lower. A typical ADC conversion requires 16 ADC clocks plus the selected acquisition time. The divider ratio is selected as follows: MCLK Divider CK0 CK1 32 0 0 4 (Do not use with a CD setting of 0) 1 0 8 0 1 2 1 1 The ADC acquisition select bits (AQ1, AQ0) select the time provided for the input track-and-hold amplifier to acquire the input signal. An acquisition of three or more ADC clocks is recommended; clocks are as follows: No. ADC Clks AQ0 AQ1 1 0 0 2 1 0 3 0 1 4 1 1 The Timer 2 conversion bit (T2C) is set by the user to enable the Timer 2 overflow bit to be used as the ADC conversion start trigger input. The external trigger enable bit (EXC) is set by the user to allow the external Pin P3.5 (CONVST) to be used as the active low convert start input. This input should be an active low pulse (minimum pulse width >100 ns) at the required sample rate.
6 5 4
EXT_REF CK1 CK0
3 2
AQ1 AQ0
1 0
T2C EXC
Rev. 0 | Page 24 of 88
ADuC841/ADuC842/ADuC843
ADCCON2--(ADC Control SFR 2)
The ADCCON2 register controls ADC channel selection and conversion modes as detailed below. SFR Address SFR Power-On Default Bit Addressable D8H 00H Yes
Table 8. ADCCON2 SFR Bit Designations
Bit No. 7 Name ADCI Description ADC Interrupt Bit. Set by hardware at the end of a single ADC conversion cycle or at the end of a DMA block conversion. Cleared by hardware when the PC vectors to the ADC interrupt service routine. Otherwise, the ADCI bit is cleared by user code. DMA Mode Enable Bit. Set by the user to enable a preconfigured ADC DMA mode operation. A more detailed description of this mode is given in the ADC DMA Mode section. The DMA bit is automatically set to 0 at the end of a DMA cycle. Setting this bit causes the ALE output to cease; it will start again when DMA is started and will operate correctly after DMA is complete. Continuous Conversion Bit. Set by the user to initiate the ADC into a continuous mode of conversion. In this mode, the ADC starts converting based on the timing and channel configuration already set up in the ADCCON SFRs; the ADC automatically starts another conversion once a previous conversion has completed. Single Conversion Bit. Set to initiate a single conversion cycle. The SCONV bit is automatically reset to 0 on completion of the single conversion cycle. Channel Selection Bits. Allow the user to program the ADC channel selection under software control. When a conversion is initiated, the converted channel is the one pointed to by these channel selection bits. In DMA mode, the channel selection is derived from the channel ID written to the external memory. CH# CS0 CS1 CS2 CS3 0 0 0 0 0 1 1 0 0 0 2 0 1 0 0 3 1 1 0 0 4 0 0 1 0 5 1 0 1 0 6 0 1 1 0 7 1 1 1 0 Temp Monitor Requires minimum of 1 s to acquire. 0 0 0 1 DAC0 1 0 0 Only use with internal DAC output buffer on. 1 DAC1 0 1 0 Only use with internal DAC output buffer on. 1 AGND 1 1 0 1 VREF 0 0 1 1 1 1 1 1 DMA STOP Place in XRAM location to finish DMA sequence; refer to the ADC DMA Mode section. All other combinations reserved.
6
DMA
5
CCONV
4
SCONV
3 2 1 0
CS3 CS2 CS1 CS0
Rev. 0 | Page 25 of 88
ADuC841/ADuC842/ADuC843
ADCCON3--(ADC Control SFR 3)
The ADCCON3 register controls the operation of various calibration modes and also indicates the ADC busy status. SFR Address SFR Power-On Default Bit Addressable F5H 00H No
Table 9. ADCCON3 SFR Bit Designations
Bit No. 7 Name BUSY Description ADC Busy Status Bit. A read-only status bit that is set during a valid ADC conversion or during a calibration cycle. Busy is automatically cleared by the core at the end of conversion or calibration. Reserved. This bit should always be written as 0. Number of Average Selection Bits. This bit selects the number of ADC readings that are averaged during a calibration cycle. Number of Averages AVGS0 AVGS1 15 0 0 1 1 0 31 0 1 63 1 1 Reserved. This bit should always be written as 0. This bit should always be written as 1 by the user when performing calibration. Calibration Type Select Bit. This bit selects between offset (zero-scale) and gain (full-scale) calibration. Set to 0 for offset calibration. Set to 1 for gain calibration. Start Calibration Cycle Bit. When set, this bit starts the selected calibration cycle. It is automatically cleared when the calibration cycle is completed.
6 5 4
RSVD AVGS1 AVGS0
3 2 1
RSVD RSVD TYPICAL
0
SCAL
Rev. 0 | Page 26 of 88
ADuC841/ADuC842/ADuC843
The ADC incorporates a successive approximation architecture (SAR) involving a charge-sampled input stage. Figure 30 shows the equivalent circuit of the analog input section. Each ADC conversion is divided into two distinct phases, as defined by the position of the switches in Figure 30. During the sampling phase (with SW1 and SW2 in the track position), a charge proportional to the voltage on the analog input is developed across the input sampling capacitor. During the conversion phase (with both switches in the hold position), the capacitor DAC is adjusted via internal SAR logic until the voltage on Node A is 0, indicating that the sampled charge on the input capacitor is balanced out by the charge being output by the capacitor DAC. The final digital value contained in the SAR is then latched out as the result of the ADC conversion. Control of the SAR and timing of acquisition and sampling modes is handled automatically by built-in ADC control logic. Acquisition and conversion times are also fully configurable under user control.
ADuC841/ADuC842/ADuC843
VREF AGND DAC1 DAC0 TEMPERATURE MONITOR AIN7
kHz sample rate. Though the R/C does help to reject some incoming high frequency noise, its primary function is to ensure that the transient demands of the ADC input stage are met.
ADuC841/ ADuC842/ ADuC843
10 AIN0 0.1 F
03260-0-029
Figure 31. Buffering Analog Inputs
200 AIN0 TRACK HOLD 32pF 200 NODE A sw2 HOLD sw1
CAPACITOR DAC
COMPARATOR
It does so by providing a capacitive bank from which the 32 pF sampling capacitor can draw its charge. Its voltage does not change by more than one count (1/4096) of the 12-bit transfer function when the 32 pF charge from a previous channel is dumped onto it. A larger capacitor can be used if desired, but not a larger resistor (for reasons described below). The Schottky diodes in Figure 31 may be necessary to limit the voltage applied to the analog input pin per the Absolute Maximum Ratings. They are not necessary if the op amp is powered from the same supply as the part since in that case the op amp is unable to generate voltages above VDD or below ground. An op amp of some kind is necessary unless the signal source is very low impedance to begin with. DC leakage currents at the parts' analog inputs can cause measurable dc errors with external source impedances as low as 100 or so. To ensure accurate ADC operation, keep the total source impedance at each analog input less than 61 . The Table 10 illustrates examples of how source impedance can affect dc accuracy. Table 10. Source Impedance and DC Accuracy
Source Impedance 61 610 Error from 1 A Leakage Current 61 V = 0.1 LSB 610 V = 1 LSB Error from 10 A Leakage Current 610 V = 1 LSB 6.1 mV = 10 LSB
AGND
Figure 30. Internal ADC Structure
Note that whenever a new input channel is selected, a residual charge from the 32 pF sampling capacitor places a transient on the newly selected input. The signal source must be capable of recovering from this transient before the sampling switches go into hold mode. Delays can be inserted in software (between channel selection and conversion request) to account for input stage settling, but a hardware solution alleviates this burden from the software design task and ultimately results in a cleaner system implementation. One hardware solution is to choose a very fast settling op amp to drive each analog input. Such an op amp would need to fully settle from a small signal transient in less than 300 ns in order to guarantee adequate settling under all software configurations. A better solution, recommended for use with any amplifier, is shown in Figure 31. Though at first glance the circuit in Figure 31 may look like a simple antialiasing filter, it actually serves no such purpose since its corner frequency is well above the Nyquist frequency, even at a 200
03260-0-028
TRACK
Although Figure 31 shows the op amp operating at a gain of 1, one can, of course, configure it for any gain needed. Also, one can just as easily use an instrumentation amplifier in its place to condition differential signals. Use an amplifier that is capable of delivering the signal (0 V to VREF) with minimal saturation. Some single-supply rail-to-rail op amps that are useful for this purpose are described in Table 11. Check Analog Devices website www.analog.com for details on these and other op amps and instrumentation amps.
Rev. 0 | Page 27 of 88
ADuC841/ADuC842/ADuC843
Table 11. Some Single-Supply Op Amps
Op Amp Model OP281/OP481 OP191/OP291/OP491 OP196/OP296/OP496 OP183/OP283 OP162/OP262/OP462 AD820/AD822/AD824 AD823 Characteristics Micropower I/O Good up to VDD, Low Cost I/O to VDD, Micropower, Low Cost High Gain-Bandwidth Product High GBP, Micro Package FET Input, Low Cost FET Input, High GBP
If an external voltage reference is preferred, it should be connected to the CREF pin as shown in Figure 33. Bit 6 of the ADCCON1 SFR must be set to 1 to switch in the external reference voltage. To ensure accurate ADC operation, the voltage applied to CREF must be between 1 V and AVDD. In situations where analog input signals are proportional to the power supply (such as in some strain gage applications), it may be desirable to connect the CREF pin directly to AVDD. Operation of the ADC or DACs with a reference voltage below 1 V, however, may incur loss of accuracy, eventually resulting in missing codes or nonmonotonicity. For that reason, do not use a reference voltage lower than 1 V.
ADuC841/ADuC842/ADuC843
VDD EXTERNAL VOLTAGE REFERENCE 51 2.5V BAND GAP REFERENCE BUFFER 0 = INTERNAL
VREF = NC
Keep in mind that the ADC's transfer function is 0 V to VREF, and that any signal range lost to amplifier saturation near ground will impact dynamic range. Though the op amps in Table 11 are capable of delivering output signals that very closely approach ground, no amplifier can deliver signals all the way to ground when powered by a single supply. Therefore, if a negative supply is available, you might consider using it to power the front end amplifiers. If you do, however, be sure to include the Schottky diodes shown in Figure 31 (or at least the lower of the two diodes) to protect the analog input from undervoltage conditions. To summarize this section, use the circuit in Figure 31 to drive the analog input pins of the parts.
1 = EXTERNAL ADCCON1.6
Voltage Reference Connections
The on-chip 2.5 V band gap voltage reference can be used as the reference source for the ADC and DACs. To ensure the accuracy of the voltage reference, you must decouple the CREF pin to ground with a 0.47 F capacitor, as shown in Figure 32. Note that this is different from the ADuC812/ADuC831/ADuC832.
ADuC841/ADuC842/ADuC843
51 2.5V BAND GAP REFERENCE
CREF 0.1 F
Figure 33. Using an External Voltage Reference
Configuring the ADC
The parts' successive approximation ADC is driven by a divided down version of the master clock. To ensure adequate ADC operation, this ADC clock must be between 400 kHz and 8.38 MHz. Frequencies within this range can be achieved easily with master clock frequencies from 400 kHz to well above 16 MHz, with the four ADC clock divide ratios to choose from. For example, set the ADC clock divide ratio to 8 (i.e., ADCCLK = 16.777216 MHz/8 = 2 MHz) by setting the appropriate bits in ADCCON1 (ADCCON1.5 = 1, ADCCON1.4 = 0). The total ADC conversion time is 15 ADC clocks, plus 1 ADC clock for synchronization, plus the selected acquisition time (1, 2, 3, or 4 ADC clocks). For the preceding example, with a 3-clock acquisition time, total conversion time is 19 ADC clocks (or 9.05 s for a 2 MHz ADC clock). In continuous conversion mode, a new conversion begins each time the previous one finishes. The sample rate is then simply the inverse of the total conversion time described previously. In the preceding example, the continuous conversion mode sample rate is 110.3 kHz.
BUFFER VREF = NC
CREF
03260-0-030
BUFFER
0.47F
Figure 32. Decoupling VREF and CREF
If the internal voltage reference is to be used as a reference for external circuitry, the CREF output should be used. However, a buffer must be used in this case to ensure that no current is drawn from the CREF pin itself. The voltage on the CREF pin is that of an internal node within the buffer block, and its voltage is critical for ADC and DAC accuracy. The parts power up with their internal voltage reference in the off state.
Rev. 0 | Page 28 of 88
03260-0-031
ADuC841/ADuC842/ADuC843
If using the temperature sensor as the ADC input, the ADC should be configured to use an ADCCLK of MCLK/32 and four acquisition clocks. Increasing the conversion time on the temperature monitor channel improves the accuracy of the reading. To further improve the accuracy, an external reference with low temperature drift should also be used.
00000AH 1 0 0 1 0 000000H 0 1 0 0 0 1 0 1 1 1 0 0 1 1 1 1 0 1 0 STOP COMMAND REPEAT LAST CHANNEL FOR A VALID STOP CONDITION CONVERT ADC CH 3 CONVERT TEMP SENSOR CONVERT ADC CH 5 CONVERT ADC CH 2
ADC DMA Mode
The on-chip ADC has been designed to run at a maximum conversion speed of 2.38 s (420 kHz sampling rate). When converting at this rate, the ADuC841/ADuC842/ADuC843 MicroConverter has 2 s to read the ADC result and to store the result in memory for further postprocessing; otherwise the next ADC sample could be lost. In an interrupt driven routine, the MicroConverter would also have to jump to the ADC interrupt service routine, which also increases the time required to store the ADC results. In applications where the parts cannot sustain the interrupt rate, an ADC DMA mode is provided. To enable DMA mode, Bit 6 in ADCCON2 (DMA) must be set, which allows the ADC results to be written directly to a 16 MByte external static memory SRAM (mapped into data memory space) without any interaction from the core of the part. This mode allows the part to capture a contiguous sample stream at full ADC update rates (420 kHz). Typical DMA Mode Configuration Example Setting the parts to DMA mode consists of the following steps: 1. 2. The ADC must be powered down. This is done by ensuring that MD1 and MD0 are both set to 0 in ADCCON1. The DMA address pointer must be set to the start address of where the ADC results are to be written. This is done by writing to the DMA mode address pointers DMAL, DMAH, and DMAP. DMAL must be written to first, followed by DMAH, and then by DMAP. The external memory must be preconfigured. This consists of writing the required ADC channel IDs into the top four bits of every second memory location in the external SRAM, starting at the first address specified by the DMA address pointer. Because the ADC DMA mode operates independently from the ADuC841/ADuC842/ADuC843 core, it is necessary to provide it with a stop command. This is done by duplicating the last channel ID to be converted followed by 1111 into the next channel selection field. A typical preconfiguration of external memory is shown in Figure 34.
Figure 34. Typical DMA External Memory Preconfiguration
4.
The DMA is initiated by writing to the ADC SFRs in the following sequence: a. b. ADCCON2 is written to enable the DMA mode, i.e., MOV ADCCON2, #40H; DMA mode enabled. ADCCON1 is written to configure the conversion time and power-up of the ADC. It can also enable Timer 2 driven conversions or external triggered conversions if required. ADC conversions are initiated. This is done by starting single conversions, starting Timer 2, running for Timer 2 conversions, or receiving an external trigger.
c.
When the DMA conversions are complete, the ADC interrupt bit, ADCI, is set by hardware, and the external SRAM contains the new ADC conversion results as shown in Figure 35. Note that no result is written to the last two memory locations. When the DMA mode logic is active, it takes the responsibility of storing the ADC results away from both the user and the core logic of the part. As the DMA interface writes the results of the ADC conversions to external memory, it takes over the external memory interface from the core. Thus, any core instructions that access the external memory while DMA mode is enabled does not get access to the external memory. The core executes the instructions, and they take the same time to execute, but they cannot access the external memory.
00000A H 1 0 0 1 0 000000H 0 1 0 0 0 1 0 1 1 1 0 0 1 1 1 1 0 1 0 STOP COMMAND NO CONVERSION RESULT WRITTEN HERE CONVERSION RESULT FOR ADC CH 3 CONVERSION RESULT FOR TEMP SENSOR CONVERSION RESULT FOR ADC CH 5 CONVERSION RESULT FOR ADC CH 2
03260-0-034
3.
Figure 35. Typical External Memory Configuration Post ADC DMA Operation
Rev. 0 | Page 29 of 88
03260-0-033
ADuC841/ADuC842/ADuC843
The DMA logic operates from the ADC clock and uses pipelining to perform the ADC conversions and to access the external memory at the same time. The time it takes to perform one ADC conversion is called a DMA cycle. The actions performed by the logic during a typical DMA cycle are shown in Figure 36.
CONVERT CHANNEL READ DURING PREVIOUS DMA CYCLE
ADC Offset and Gain Calibration Coefficients
The ADuC841/ADuC842/ADuC843 have two ADC calibration coefficients, one for offset calibration and one for gain calibration. Both the offset and gain calibration coefficients are 14-bit words, and are each stored in two registers located in the special function register (SFR) area. The offset calibration coefficient is divided into ADCOFSH (six bits) and ADCOFSL (8 bits), and the gain calibration coefficient is divided into ADCGAINH (6 bits) and ADCGAINL (8 bits). The offset calibration coefficient compensates for dc offset errors in both the ADC and the input signal. Increasing the offset coefficient compensates for positive offset, and effectively pushes the ADC transfer function down. Decreasing the offset coefficient compensates for negative offset, and effectively pushes the ADC transfer function up. The maximum offset that can be compensated is typically 5% of VREF, which equates to typically 125 mV with a 2.5 V reference. Similarly, the gain calibration coefficient compensates for dc gain errors in both the ADC and the input signal. Increasing the gain coefficient compensates for a smaller analog input signal range and scales the ADC transfer function up, effectively increasing the slope of the transfer function. Decreasing the gain coefficient compensates for a larger analog input signal range and scales the ADC transfer function down, effectively decreasing the slope of the transfer function. The maximum analog input signal range for which the gain coefficient can compensate is 1.025 x VREF, and the minimum input range is 0.975 x VREF, which equates to typically 2.5% of the reference voltage.
DMA CYCLE
Figure 36. DMA Cycle
Figure 36 shows that during one DMA cycle, the following actions are performed by the DMA logic: 1. 2. An ADC conversion is performed on the channel whose ID was read during the previous cycle. The 12-bit result and the channel ID of the conversion performed in the previous cycle is written to the external memory. The ID of the next channel to be converted is read from external memory.
3.
For the previous example, the complete flow of events is shown in Figure 36. Because the DMA logic uses pipelining, it takes three cycles before the first correct result is written out.
Micro Operation during ADC DMA Mode
During ADC DMA mode, the MicroConverter core is free to continue code execution, including general housekeeping and communication tasks. However, note that MCU core accesses to Ports 0 and 2 (which of course are being used by the DMA controller) are gated off during the ADC DMA mode of operation. This means that even though the instruction that accesses the external Ports 0 or 2 appears to execute, no data is seen at these external ports as a result. Note that during DMA to the internally contained XRAM, Ports 0 and 2 are available for use. The only case in which the MCU can access XRAM during DMA is when the internal XRAM is enabled and the section of RAM to which the DMA ADC results are being written to lies in an external XRAM. Then the MCU can access the internal XRAM only. This is also the case for use of the extended stack pointer. The MicroConverter core can be configured with an interrupt to be triggered by the DMA controller when it has finished filling the requested block of RAM with ADC results, allowing the service routine for this interrupt to postprocess data without any real-time timing constraints.
03260-0-035
WRITE ADC RESULT CONVERTED DURING PREVIOUS DMA CYCLE
READ CHANNEL ID TO BE CONVERTED DURING NEXT DMA CYCLE
CALIBRATING THE ADC
Two hardware calibration modes are provided, which can be easily initiated by user software. The ADCCON3 SFR is used to calibrate the ADC. Bit 1 (typical) and CS3 to CS0 (ADCCON2) set up the calibration modes. Device calibration can be initiated to compensate for significant changes in operating condition frequency, analog input range, reference voltage, and supply voltages. In this calibration mode, offset calibration uses internal AGND selected via ADCCON2 register Bits CS3 to CS0 (1011), and gain calibration uses internal VREF selected by Bits CS3 to CS0 (1100). Offset calibration should be executed first, followed by gain calibration. System calibration can be initiated to compensate for both internal and external system errors. To perform system calibration by using an external reference, tie the system ground and reference to any two of the six selectable inputs. Enable external reference mode (ADCCON1.6). Select the channel connected to AGND via Bits CS3 to CS0 and perform system offset calibration. Select the channel connected to VREF via Bits CS3 to CS0 and perform system gain calibration.
Rev. 0 | Page 30 of 88
ADuC841/ADuC842/ADuC843
Initiating the Calibration in Code
When calibrating the ADC using ADCCON1, the ADC must be set up into the configuration in which it will be used. The ADCCON3 register can then be used to set up the device and to calibrate the ADC offset and gain.
MOV ADCCON1,#08CH ; ADC on; ADCCLK set ;to divide by 32,4 ;acquisition clock
NONVOLATILE FLASH/EE MEMORY
The ADuC841/ADuC842/ADuC843 incorporate Flash/EE memory technology on-chip to provide the user with nonvolatile, in-circuit, reprogrammable code and data memory space. Flash/EE memory is a relatively recent type of nonvolatile memory technology, which is based on a single transistor cell architecture. Flash/EE memory combines the flexible in-circuit reprogrammable features of EEPROM with the space efficient/ density features of EPROM as shown in Figure 37. Because Flash/EE technology is based on a single transistor cell architecture, a flash memory array, such as EPROM, can be implemented to achieve the space efficiencies or memory densities required by a given design. Like EEPROM, flash memory can be programmed in-system at a byte level; it must first be erased, the erase being performed in page blocks. Thus, flash memory is often and more correctly referred to as Flash/EE memory.
EPROM TECHNOLOGY EEPROM TECHNOLOGY
To calibrate device offset:
MOV ADCCON2,#0BH MOV ADCCON3,#25H ;select internal AGND ;select offset calibration, ;31 averages per bit, ;offset calibration
To calibrate device gain:
MOV ADCCON2,#0CH MOV ADCCON3,#27H ;select internal VREF ;select offset calibration, ;31 averages per bit, ;offset calibration
To calibrate system offset, connect system AGND to an ADC channel input (0).
MOV ADCCON2,#00H MOV ADCCON3,#25H ;select external AGND ;select offset calibration, ;31 averages per bit
SPACE EFFICIENT/ DENSITY
IN-CIRCUIT REPROGRAMMABLE FLASH/EEMEMORY TECHNOLOGY
03260-0-036
To calibrate system gain, connect system VREF to an ADC channel input (1).
MOV ADCCON2,#01H MOV ADCCON3,#27H ;select external VREF ;select offset calibration, ;31 averages per bit, ;offset calibration
Figure 37. Flash/EE Memory Development
The calibration cycle time TCAL is calculated by the following equation:
Overall, Flash/EE memory represents a step closer to the ideal memory device that includes nonvolatility, in-circuit programmability, high density, and low cost. Incorporated in the parts, Flash/EE memory technology allows the user to update program code space in-circuit, without the need to replace one-time programmable (OTP) devices at remote operating nodes.
TCAL = 14 x ADCCLK x NUMAV x 16 + TACQ
(
)
Flash/EE Memory and the ADuC841/ADuC842/ADuC843
The parts provide two arrays of Flash/EE memory for user applications. Up to 62 kBytes of Flash/EE program space are provided on-chip to facilitate code execution without any external discrete ROM device requirements. The program memory can be programmed in-circuit by using the serial download mode provided, by using conventional third party memory programmers, or via a user defined protocol that can configure it as data if required. Note that the following sections use the 62 kByte program space as an example when referring to ULOAD mode. For the other memory models (32 kByte and 8 kByte), the ULOAD space moves to the top 8 kBytes of the on-chip program memory, i.e., for 32 kBytes, the ULOAD space is from 24 kBytes to 32 kBytes, the kernel still resides in a protected space from 60 kBytes to 62 kBytes. There is no ULOAD space present on the 8 kBtye part.
For an ADCCLK/FCORE divide ratio of 32, TACQ = 4 ADCCLK, and NUMAV = 15, the calibration cycle time is
TCAL = 14 x (1 / 524288) x 15 x (16 + 4) TCAL = 8 ms
In a calibration cycle, the ADC busy flag (Bit 7), instead of framing an individual ADC conversion as in normal mode, goes high at the start of calibration and returns to zero only at the end of the calibration cycle. It can therefore be monitored in code to indicate when the calibration cycle is completed. The following code can be used to monitor the BUSY signal during a calibration cycle:
WAIT: MOV A, ADCCON3 JB ACC.7, WAIT ;move ADCCON3 to A ;If Bit 7 is set jump to WAIT else continue
Rev. 0 | Page 31 of 88
ADuC841/ADuC842/ADuC843
A 4 kByte Flash/EE data memory space is also provided onchip. This may be used as a general-purpose nonvolatile scratchpad area. User access to this area is via a group of six SFRs. This space can be programmed at a byte level, although it must first be erased in 4-byte pages.
300
250
RETENTION (Years)
200
Flash/EE Memory Reliability
The Flash/EE program and data memory arrays on the parts are fully qualified for two key Flash/EE memory characteristics: Flash/EE memory cycling endurance and Flash/EE memory data retention. Endurance quantifies the ability of the Flash/EE memory to be cycled through many program, read, and erase cycles. In real terms, a single endurance cycle is composed of four independent, sequential events, defined as 1. 2. 3. 4. Initial page erase sequence. Read/verify sequence a single Flash/EE. Byte program sequence memory. Second read/verify sequence endurance cycle.
150
ADI SPECIFICATION 100 YEARS MIN. AT TJ = 55C
100
50
03260-0-037
0 40
50
60 70 90 80 TJ JUNCTION TEMPERATURE (C)
100
110
Figure 38. Flash/EE Memory Data Retention
Using the Flash/EE Program Memory
The 62 kByte Flash/EE program memory array is mapped into the lower 62 kBytes of the 64 kByte program space addressable by the parts, and is used to hold user code in typical applications. The program Flash/EE memory array can be programmed in three ways:
Serial Downloading (In-Circuit Programming)
In reliability qualification, every byte in both the program and data Flash/EE memory is cycled from 00H to FFH until a first fail is recorded, signifying the endurance limit of the on-chip Flash/EE memory. As indicated in the Specifications table, the parts' Flash/EE memory endurance qualification has been carried out in accordance with JEDEC Retention Lifetime Specification A117 over the industrial temperature range of -40C to +25C and +25C to +85C. The results allow the specification of a minimum endurance figure over supply and over temperature of 100,000 cycles, with an endurance figure of 700,000 cycles being typical of operation at 25C. Retention quantifies the ability of the Flash/EE memory to retain its programmed data over time. Again, the parts have been qualified in accordance with the formal JEDEC Retention Lifetime Specification (A117) at a specific junction temperature (TJ = 55C). As part of this qualification procedure, the Flash/EE memory is cycled to its specified endurance limit, described previously, before data retention is characterized. This means that the Flash/EE memory is guaranteed to retain its data for its fully specified retention lifetime every time the Flash/EE memory is reprogrammed. Also note that retention lifetime, based on an activation energy of 0.6 eV, derates with TJ as shown in Figure 38.
The parts facilitate code download via the standard UART serial port. The parts enter serial download mode after a reset or power cycle if the PSEN pin is pulled low through an external 1 k resistor. Once in serial download mode, the user can download code to the full 62 kBytes of Flash/EE program memory while the device is in-circuit in its target application hardware. A PC serial download executable is provided as part of the ADuC841/ADuC842 QuickStart development system. The serial download protocol is detailed in MicroConverter Application Note uC004.
Parallel Programming
Parallel programming mode is fully compatible with conventional third party flash or EEPROM device programmers. In this mode, Ports P0, P1, and P2 operate as the external data and address bus interface, ALE operates as the write enable strobe, and Port P3 is used as a general configuration port, which configures the device for various program and erase operations during parallel programming. The high voltage (12 V) supply required for flash programming is generated using on-chip charge pumps to supply the high voltage program lines. The complete parallel programming specification is available on the MicroConverter home page at www.analog.com/microconverter.
Rev. 0 | Page 32 of 88
ADuC841/ADuC842/ADuC843
User Download Mode (ULOAD)
EMBEDDED DOWNLOAD/DEBUG KERNEL PERMANENTLY EMBEDDED FIRMWARE ALLOWS CODE TO BE DOWNLOADED TO ANY OF THE 32 kBYTES OF ON-CHIP PROGRAM MEMORY. THE KERNEL PROGRAM APPEARS AS 'NOP' INSTRUCTIONS TO USER CODE USER BOOTLOADER SPACE THE USER BOOTLOADER SPACE CAN BE PROGRAMMED IN DOWNLOAD/DEBUG MODE VIA THE KERNEL BUT IS READ ONLY WHEN EXECUTING USER CODE USER DOWNLOADER SPACE
03260-0-039
Figure 39 shows that it is possible to use the 62 kBytes of Flash/EE program memory available to the user as a single block of memory. In this mode, all of the Flash/EE memory is read-only to user code.
However, the Flash/EE program memory can also be written to during runtime simply by entering ULOAD mode. In ULOAD mode, the lower 56 kBytes of program memory can be erased and reprogrammed by user software as shown in Figure 39. ULOAD
FFFFH 2kBYTE F800H F7FFH NOP'S 8000H 7FFFH 8kBYTE 6000H
32 kBYTES OF USER CODE MEMORY
mode can be used to upgrade your code in the field via any user defined download protocol. By configuring the SPI port on the part as a slave, it is possible to completely reprogram the 56 kBytes of Flash/EE program memory in only 5 seconds (refer to Application Note uC007). Alternatively, ULOAD mode can be used to save data to the 56 kBytes of Flash/EE memory. This can be extremely useful in data logging applications where the part can provide up to 60 kBytes of NV data memory on chip (4 kBytes of dedicated Flash/EE data memory also exist). The upper 6 kBytes of the 62 kBytes of Flash/EE program memory are programmable only via serial download or parallel programming. This means that this space appears as read-only to user code. Therefore, it cannot be accidentally erased or reprogrammed by erroneous code execution, which makes it very suitable to use the 6 kBytes as a bootloader. A bootload enable option exists in the serial downloader to "always run from E000H after reset." If using a bootloader, this option is recommended to ensure that the bootloader always executes correct code after reset. Programming the Flash/EE program memory via ULOAD mode is described in more detail in the description of ECON and in Application Note uC007.
EMBEDDED DOWNLOAD/DEBUG KERNEL PERMANENTLY EMBEDDED FIRMWARE ALLOWS CODE TO BE DOWNLOADED TO ANY OF THE 62 kBYTES OF ON-CHIP PROGRAM MEMORY. THE KERNEL PROGRAM APPEARS AS 'NOP' INSTRUCTIONS TO USER CODE USER BOOTLOADER SPACE THE USER BOOTLOADER SPACE CAN BE PROGRAMMED IN DOWNLOAD/DEBUG MODE VIA THE KERNEL BUT IS READ ONLY WHEN EXECUTING USER CODE USER DOWNLOADER SPACE EITHER THE DOWNLOAD/DEBUG KERNEL OR USER CODE (IN ULOAD MODE) CAN PROGRAM THIS SPACE FFFFH 2kBYTE F800H F7FFH 6kBYTE E000H
EITHER THE DOWNLOAD/DEBUG KERNEL OR USER CODE (IN ULOAD MODE) CAN PROGRAM THIS SPACE
5FFFH 26kBYTE 0000H
Figure 40. Flash/EE Program Memory Map in ULOAD Mode (32 kByte Part)
Flash/EE Program Memory Security
The ADuC841/ADuC842/ADuC843 facilitate three modes of Flash/EE program memory security. These modes can be independently activated, restricting access to the internal code space. These security modes can be enabled as part of serial download protocol as described in Application Note uC004 or via parallel programming. The security modes available on the parts are as follows:
Lock Mode
This mode locks the code memory, disabling parallel programming of the program memory. However, reading the memory in parallel mode and reading the memory via a MOVC command from external memory is still allowed. This mode is deactivated by initiating a code-erase command in serial download or parallel programming modes.
Secure Mode
This mode locks code in memory, disabling parallel programming (program and verify/read commands) as well as disabling the execution of a MOVC instruction from external memory, which is attempting to read the op codes from internal memory. Read/write of internal data Flash/EE from external memory is also disabled. This mode is deactivated by initiating a code-erase command in serial download or parallel programming modes.
Serial Safe Mode
62 kBYTES OF USER CODE MEMORY
dFFFH 56kBYTE 0000H
03260-0-038
Figure 39. Flash/EE Program Memory Map in ULOAD Mode (62 kByte Part)
This mode disables serial download capability on the device. If serial safe mode is activated and an attempt is made to reset the part into serial download mode, i.e., RESET asserted and deasserted with PSEN low, the part interprets the serial download reset as a normal reset only. It therefore cannot enter serial download mode but can only execute as a normal reset sequence. Serial safe mode can be disabled only by initiating a code-erase command in parallel programming mode.
Rev. 0 | Page 33 of 88
ADuC841/ADuC842/ADuC843
USING FLASH/EE DATA MEMORY
The 4 kBytes of Flash/EE data memory are configured as 1024 pages, each of 4 bytes. As with the other ADuC841/ADuC842/ ADuC843 peripherals, the interface to this memory space is via a group of registers mapped in the SFR space. A group of four data registers (EDATA1-4) is used to hold the four bytes of data at each page. The page is addressed via the two registers, EADRH and EADRL. Finally, ECON is an 8-bit control register that may be written with one of nine Flash/EE memory access commands to trigger various read, write, erase, and verify functions. A block diagram of the SFR interface to the Flash/EE data memory array is shown in Figure 41.
3FFH 3FEH
PAGE ADDRESS (EADRH/L)
BYTE 1 (0FFCH) BYTE 1 (0FF8H)
BYTE 2 (0FFDH) BYTE 2 (0FF9H)
BYTE 3 (0FFEH) BYTE 3 (0FFAH)
BYTE 4 (0FFFH) BYTE 4 (0FFBH)
03H 02H 01H 00H
BYTE 1 (000CH) BYTE 1 (0008H) BYTE 1 (0004H) BYTE 1 (0000H)
EDATA1 SFR
BYTE 2 (000DH) BYTE 2 (0009H) BYTE 2 (0005H) BYTE 2 (0001H)
EDATA2 SFR
BYTE 3 (000EH) BYTE 3 (000AH) BYTE 3 (0006H) BYTE 3 (0002H)
EDATA3 SFR
BYTE 4 (000FH)
BYTE 4 (000BH)
BYTE 4 (0007H) BYTE 4 (0003H)
EDATA4 SFR
ECON--Flash/EE Memory Control SFR
Programming of either Flash/EE data memory or Flash/ EE program memory is done through the Flash/EE memory control SFR (ECON). This SFR allows the user to read, write, erase, or verify the 4 kBytes of Flash/EE data memory or the 56 kBytes of Flash/EE program memory.
Table 12. ECON--Flash/EE Memory Commands
ECON VALUE 01H READ 02H WRITE
Figure 41. Flash/EE Data Memory Control and Configuration
Command Description (Normal Mode) (Power-On Default) Results in 4 bytes in the Flash/EE data memory, addressed by the page address EADRH/L, being read into EDATA1-4. Results in 4 bytes in EDATA1-4 being written to the Flash/EE data memory at the page address given by EADRH/L (0 - EADRH/L < 0400H). Note that the 4 bytes in the page being addressed must be pre-erased. Reserved. Verifies that the data in EDATA1-4 is contained in the page address given by EADRH/L. A subsequent read of the ECON SFR results in 0 being read if the verification is valid, or a nonzero value being read to indicate an invalid verification. Results in erasing the 4-byte page of Flash/EE data memory addressed by the page address EADRH/L.
Command Description (ULOAD Mode) Not implemented. Use the MOVC instruction. Results in bytes 0-255 of internal XRAM being written to the 256 bytes of Flash/EE program memory at the page address given by EADRH (0 - EADRH < E0H). Note that the 256 bytes in the page being addressed must be pre-erased. Reserved. Not implemented. Use the MOVC and MOVX instructions to verify the write in software.
03H 04H VERIFY
05H ERASE PAGE
06H ERASE ALL 81H READBYTE 82H WRITEBYTE 0FH EXULOAD F0H ULOAD
Results in erasing the entire 4 kBytes of Flash/EE data memory. Results in the byte in the Flash/EE data memory, addressed by the byte address EADRH/L, being read into EDATA1 (0 - EADRH / L - 0FFFH). Results in the byte in EDATA1 being written into Flash/EE data memory at the byte address EADRH/L Leaves the ECON instructions to operate on the Flash/EE data memory. Enters ULOAD mode, directing subsequent ECON instructions to operate on the Flash/EE program memory.
Results in the 64 byte page of Flash/EE program memory, addressed by the byte address EADRH/L, being erased. EADRL can equal any of 64 locations within the page. A new page starts whenever EADRL is equal to 00H, 40H, 80H, or C0H. Results in erasing the entire 56 kBytes of ULOAD Flash/EE program memory. Not implemented. Use the MOVC command.
Results in the byte in EDATA1 being written into Flash/EE program memory at the byte address EADRH/L (0 - EADRH/L - DFFFH). Enters normal mode directing subsequent ECON instructions to operate on the Flash/EE data memory. Leaves the ECON instructions to operate on the Flash/EE program memory.
Rev. 0 | Page 34 of 88
03260-0-040
BYTE ADDRESSES ARE GIVEN IN BRACKETS
ADuC841/ADuC842/ADuC843
Example: Programming the Flash/EE Data Memory
A user wants to program F3H into the second byte on Page 03H of the Flash/EE data memory space while preserving the other 3 bytes already in this page. A typical program of the Flash/EE data array involves 1. 2. 3. Setting EADRH/L with the page address. Writing the data to be programmed to the EDATA1-4. Writing the ECON SFR with the appropriate command.
Flash/EE Memory Timing
Typical program and erase times for the parts are as follows:
Normal Mode (operating on Flash/EE data memory) READPAGE (4 bytes) 22 machine cycles WRITEPAGE (4 bytes) 380 s VERIFYPAGE (4 bytes) 22 machine cycles ERASEPAGE (4 bytes) 2 ms ERASEALL (4 kBytes) 2 ms READBYTE (1 byte) 9 machine cycles WRITEBYTE (1 byte) 200 s ULOAD Mode (operating on Flash/EE program memory) WRITEPAGE (256 bytes) 16.5 ms ERASEPAGE (64 bytes) 2 ms ERASEALL (56 kBytes) 2 ms WRITEBYTE (1 byte) 200 s
Step 1: Set Up the Page Address
Address registers EADRH and EADRL hold the high byte address and the low byte address of the page to be addressed. The assembly language to set up the address may appear as
MOV EADRH,#0 MOV EADRL,#03H ; Set Page Address Pointer
Step 2: Set Up the EDATA Registers
Write the four values to be written into the page into the four SFRs, EDATA1-4. Unfortunately, the user does not know three of them. Thus, the user must read the current page and overwrite the second byte.
MOV ECON,#1 MOV EDATA2,#0F3H ; Read Page into EDATA1-4 ; Overwrite byte 2
Step 3: Program Page
A byte in the Flash/EE array can be programmed only if it has previously been erased. To be more specific, a byte can be programmed only if it already holds the value FFH. Because of the Flash/EE architecture, this erase must happen at a page level; therefore, a minimum of 4 bytes (1 page) are erased when an erase command is initiated. Once the page is erase, the user can program the 4 bytes in-page and then perform a verification of the data.
MOV MOV MOV MOV JNZ ECON,#5 ECON,#2 ECON,#4 A,ECON ERROR ; ; ; ; ERASE Page WRITE Page VERIFY Page Check if ECON=0 (OK!)
Note that a given mode of operation is initiated as soon as the command word is written to the ECON SFR. The core microcontroller operation on the parts is idled until the requested program/read or erase mode is completed. In practice, this means that even though the Flash/EE memory mode of operation is typically initiated with a two machine cycle MOV instruction (to write to the ECON SFR), the next instruction is not executed until the Flash/EE operation is complete. This means that the core cannot respond to interrupt requests until the Flash/EE operation is complete, although the core peripheral functions like counter/timers continue to count and time as configured throughout this period.
Although the 4 kBytes of Flash/EE data memory are shipped from the factory pre-erased, i.e., byte locations set to FFH, it is nonetheless good programming practice to include an ERASEALL routine as part of any configuration/setup code running on the parts. An ERASEALL command consists of writing 06H to the ECON SFR, which initiates an erase of the 4-kByte Flash/EE array. This command coded in 8051 assembly would appear as
MOV ECON,#06H ; Erase all Command ; 2 ms Duration
Rev. 0 | Page 35 of 88
ADuC841/ADuC842/ADuC843
ADuC842/ADuC843 Configuration SFR (CFG842)
The CFG842 SFR contains the necessary bits to configure the internal XRAM, external clock select, PWM output selection, DAC buffer, and the extended SP for both the ADuC842 and the ADuC843. By default, it configures the user into 8051 mode, i.e., extended SP is disabled and internal XRAM is disabled. On the ADuC841, this register is the CFG841 register and is described on the next page.
Table 13. CFG842 SFR Bit Designations
Bit No. 7 Name EXSP Description Extended SP Enable. When set to 1 by the user, the stack rolls over from SPH/SP = 00FFH to 0100H. When set to 0 by the user, the stack rolls over from SP = FFH to SP = 00H. PWM Pin Out Selection. Set to 1 by the user to select P3.4 and P3.3 as the PWM output pins. Set to 0 by the user to select P2.6 and P2.7 as the PWM output pins. DAC Output Buffer. Set to 1 by the user to bypass the DAC output buffer. Set to 0 by the user to enable the DAC output buffer. Set by the user to 1 to select an external clock input on P3.4. Set by the user to 0 to use the internal PLL clock. Reserved. This bit should always contain 0. Reserved. This bit should always contain 0. Set to 1 by the user to move the SPI functionality of MISO, MOSI, and SCLOCK to P3.3, P3.4, and P3.5, respectively. Set to 0 by the user to leave the SPI functionality as usual on MISO, MOSI, and SCLOCK pins. XRAM Enable Bit. When set to 1 by the user, the internal XRAM is mapped into the lower 2 kBytes of the external address space. When set to 0 by the user, the internal XRAM is not accessible, and the external data memory is mapped into the lower 2 kBytes of external data memory.
CFG842
ADuC842/ADuC843 Config SFR
SFR Address Power-On Default Bit Addressable
AFH 00H No
6
PWPO
5
DBUF
4 3 2 1
EXTCLK RSVD RSVD MSPI
0
XRAMEN
Rev. 0 | Page 36 of 88
ADuC841/ADuC842/ADuC843
CFG841 ADuC841 Config SFR
SFR Address Power-On Default Bit Addressable
AFH 10H1 No
Table 14. CFG841 SFR Bit Designations
Bit No. 7 Name EXSP Description Extended SP Enable. When set to 1 by the user, the stack rolls over from SPH/SP = 00FFH to 0100H. When set to 0 by the user, the stack rolls over from SP = FFH to SP = 00H. PWM Pin Out Selection. Set to 1 by the user to select P3.4 and P3.3 as the PWM output pins. Set to 0 by the user to select P2.6 and P2.7 as the PWM output pins. DAC Output Buffer. Set to 1 by the user to bypass the DAC output buffer. Set to 0 by the user to enable the DAC output buffer. Flash/EE Controller and PWM Clock Frequency Configuration Bits. Frequency should be configured such that FOSC/Divide Factor = 32 kHz + 50%. EPM2 EPM1 EPM0 Divide Factor 0 0 0 32 0 0 1 64 0 1 0 128 0 1 1 256 1 0 0 512 1 0 1 1024 Set to 1 by the user to move the SPI functionality of MISO, MOSI, and SCLOCK to P3.3, P3.4, and P3.5, respectively. Set to 0 by the user to leave the SPI functionality as usual on MISO, MOSI, and SCLOCK pins. XRAM Enable Bit. When set to 1 by the user, the internal XRAM is mapped into the lower two kBytes of the external address space. When set to 0 by the user, the internal XRAM is not accessible, and the external data memory is mapped into the lower two kBytes of external data memory.
6
PWPO
5
DBUF
4 3 2
EPM2 EPM1 EPM0
1
MSPI
0
XRAMEN
1
Note that the Flash/EE controller bits EPM2, EPM1, EPM0 are set to their correct values depending on the crystal frequency at power-up. The user should not modify these bits so all instructions to the CFG841 register should use the ORL, XRL, or ANL instructions. Value of 10H is for 11.0592 MHz crystal.
Rev. 0 | Page 37 of 88
ADuC841/ADuC842/ADuC843
USER INTERFACE TO ON-CHIP PERIPHERALS
This section gives a brief overview of the various peripherals also available on-chip. A summary of the SFRs used to control and configure these peripherals is also given. Both DACs share a control register, DACCON, and four data registers, DAC1H/L, DAC0/L. Note that in 12-bit asynchronous mode, the DAC voltage output is updated as soon as the DACL data SFR has been written; therefore, the DAC data registers should be updated as DACH first, followed by DACL. Note that for correct DAC operation on the 0 V to VREF range, the ADC must be switched on. This results in the DAC using the correct reference value.
DACCON DAC Control Register
DAC
The ADuC841/ADuC842 incorporate two 12-bit voltage output DACs on-chip. Each has a rail-to-rail voltage output buffer capable of driving 10 k/100 pF. Each has two selectable ranges, 0 V to VREF (the internal band gap 2.5 V reference) and 0 V to AVDD. Each can operate in 12-bit or 8-bit mode.
SFR Address Power-On Default Bit Addressable
Table 15. DACCON SFR Bit Designations
Bit No. 7 Name MODE
FDH 04H No
6
RNG1
5
RNG0
4
CLR1
3
CLR0
2
SYNC
1
PD1
0
PD0
Description The DAC MODE bit sets the overriding operating mode for both DACs. Set to 1 by the user to select 8-bit mode (write 8 bits to DACxL SFR). Set to 0 by the user to select 12-bit mode. DAC1 Range Select Bit. Set to 1 by the user to select the range for DAC1 as 0 V to VDD. Set to 0 by the user to select the range for DAC1 as 0 V to VREF. DAC0 Range Select Bit. Set to 1 by the user to select the range for DAC0 as 0 V to VDD. Set to 0 by the user to select the range for DAC0 as 0 V to VREF. DAC1 Clear Bit. Set to 1 by the user to leave the output of DAC1 at its normal level. Set to 0 by the user to force the output of DAC1 to 0 V. DAC0 Clear Bit. Set to 1 by the user to leave the output of DAC0 at its normal level. Set to 0 by the user to force the output of DAC0 to 0 V. DAC0/1 Update Synchronization Bit. When set to 1, the DAC outputs update as soon as DACxL SFRs are written. The user can simultaneously update both DACs by first updating the DACxL/H SFRs while SYNC is 0. Both DACs then update simultaneously when the SYNC bit is set to 1. DAC1 Power-Down Bit. Set to 1 by the user to power on DAC1. Set to 0 by the user to power off DAC1. DAC0 Power-Down Bit. Set to 1 by the user to power on DAC0. Set to 0 by the user to power off DAC0.
DACxH/L
DAC Data Registers
Function SFR Address Power-On Default Bit Addressable
DAC data registers, written by the user to update the DAC output. DAC0L (DAC0 Data Low Byte) -> F9H; DAC1L (DAC1 Data Low Byte) -> FBH DACH (DAC0 Data High Byte) -> FAH; DAC1H (DAC1 Data High Byte) -> FCH 00H No All Four Registers. All Four Registers.
The 12-bit DAC data should be written into DACxH/L right-justified such that DACxL contains the lower 8 bits, and the lower nibble of DACxH contains the upper 4 bits.
Rev. 0 | Page 38 of 88
ADuC841/ADuC842/ADuC843
Using the DAC
The on-chip DAC architecture consists of a resistor string DAC followed by an output buffer amplifier, the functional equivalent of which is illustrated in Figure 42. Details of the actual DAC architecture can be found in U.S. Patent Number 5969657 (www.uspto.gov). Features of this architecture include inherent guaranteed monotonicity and excellent differential linearity.
ADuC841/ADuC842
AVDD VREF R OUTPUT BUFFER R DAC0 R
100mV
03260-0-042
VDD VDD-50mV VDD-100mV
50mV 0mV 000H FFFH
Figure 43. Endpoint Nonlinearities Due to Amplifier Saturation
HIGH Z DISABLE (FROM MCU) R
5
R
03260-0-041
DAC LOADED WITH 0FFFH 4
OUTPUT VOLTAGE (V)
Figure 42. Resistor String DAC Functional Equivalent
3
0
0
5 10 SOURCE/SINK CURRENT (mA)
15
Figure 45. Source and Sink Current Capability with VREF = VDD = 3 V
Rev. 0 | Page 39 of 88
03260-0-044
As shown in Figure 42, the reference source for each DAC is user selectable in software. It can be either AVDD or VREF. In 0 V-to-AVDD mode, the DAC output transfer function spans from 0 V to the voltage at the AVDD pin. In 0 V-to-VREF mode, the DAC output transfer function spans from 0 V to the internal VREF or, if an external reference is applied, the voltage at the CREF pin. The DAC output buffer amplifier features a true rail-to-rail output stage implementation. This means that unloaded, each output is capable of swinging to within less than 100 mV of both AVDD and ground. Moreover, the DAC's linearity specification (when driving a 10 k resistive load to ground) is guaranteed through the full transfer function except Codes 0 to 100, and, in 0 V-to-AVDD mode only, Codes 3995 to 4095. Linearity degradation near ground and VDD is caused by saturation of the output amplifier, and a general representation of its effects (neglecting offset and gain error) is illustrated in Figure 43. The dotted line in Figure 43 indicates the ideal transfer function, and the solid line represents what the transfer function might look like with endpoint nonlinearities due to saturation of the output amplifier. Note that Figure 43 represents a transfer function in 0 V-to-VDD mode only. In 0 V-to-VREF mode (with VREF < VDD), the lower nonlinearity would be similar, but the upper portion of the transfer function would follow the ideal line right to the end (VREF in this case, not VDD), showing no signs of endpoint linearity errors.
2
1 DAC LOADED WITH 0000H 0
03260-0-043
0
5 10 SOURCE/SINK CURRENT (mA)
15
Figure 44. Source and Sink Current Capability with VREF = VDD = 5 V
4
DAC LOADED WITH 0FFFH
OUTPUT VOLTAGE (V)
3
1
DAC LOADED WITH 0000H
ADuC841/ADuC842/ADuC843
The endpoint nonlinearities illustrated in Figure 43 become worse as a function of output loading. Most of the part's specifications assume a 10 k resistive load to ground at the DAC output. As the output is forced to source or sink more current, the nonlinear regions at the top or bottom (respectively) of Figure 43 become larger. Larger current demands can significantly limit output voltage swing. Figure 44 and Figure 45 illustrate this behavior. Note that the upper trace in each of these figures is valid only for an output range selection of 0 V-to-AVDD. In 0 V-to-VREF mode, DAC loading does not cause high-side voltage drops as long as the reference voltage remains below the upper trace in the corresponding figure. For example, if AVDD = 3 V and VREF = 2.5 V, the high-side voltage is not be affected by loads less than 5 mA. But somewhere around 7 mA, the upper curve in Figure 45 drops below 2.5 V (VREF), indicating that at these higher currents the output is not capable of reaching VREF. To reduce the effects of the saturation of the output amplifier at values close to ground and to give reduced offset and gain errors, the internal buffer can be bypassed. This is done by setting the DBUF bit in the CFG841/CFG842 register. This allows a full rail-to-rail output from the DAC, which should then be buffered externally using a dual-supply op amp in order to get a rail-torail output. This external buffer should be located as close as physically possible to the DAC output pin on the PCB. Note that the unbuffered mode works only in the 0 V to VREF range. To drive significant loads with the DAC outputs, external buffering may be required (even with the internal buffer enabled), as illustrated in Figure 46. Table 11 lists some recommended op amps.
DAC0
ADuC841/ ADuC842
03260-0-045
DAC1
Figure 46. Buffering the DAC Outputs
The DAC output buffer also features a high impedance disable function. In the chip's default power-on state, both DACs are disabled, and their outputs are in a high impedance state (or three-state) where they remain inactive until enabled in software. This means that if a zero output is desired during power-up or power-down transient conditions, then a pulldown resistor must be added to each DAC output. Assuming this resistor is in place, the DAC outputs remain at ground potential whenever the DAC is disabled.
Rev. 0 | Page 40 of 88
ADuC841/ADuC842/ADuC843
ON-CHIP PLL
The ADuC842 and ADuC843 are intended for use with a 32.768 kHz watch crystal. A PLL locks onto a multiple (512) of this to provide a stable 16.78 MHz clock for the system. The ADuC841 operates directly from an external crystal. The core can operate at this frequency or at binary submultiples of it to allow power saving in cases where maximum core performance is not required. The default core clock is the PLL clock divided by 8 or 2.097152 MHz. The ADC clocks are also derived from the PLL clock, with the modulator rate being the same as the crystal oscillator frequency. The preceding choice of frequencies ensures that the modulators and the core are synchronous, regardless of the core clock rate. The PLL control register is PLLCON. At 5 V the core clock can be set to a maximum of 16.78 MHz, while at 3 V the maximum core clock setting is 8.38 MHz. The CD bits should not be set to 0 on a 3 V part. Note that on the ADuC841, changing the CD bits in PLLCON causes the core speed to change. The core speed is crystal freq/ 2CD. The other bits in PLLCON are reserved in the case of the ADuC841 and should be written with 0.
PLLCON PLL Control Register
SFR Address Power-On Default Bit Addressable
D7H 53H No
Table 16. PLLCON SFR Bit Designations
Bit No. 7 Name OSC_PD Description Oscillator Power-Down Bit. Set by the user to halt the 32 kHz oscillator in power-down mode. Cleared by the user to enable the 32 kHz oscillator in power-down mode. This feature allows the TIC to continue counting even in power-down mode. PLL Lock Bit. This is a read-only bit. Set automatically at power-on to indicate that the PLL loop is correctly tracking the crystal clock. If the external crystal subsequently becomes disconnected, the PLL will rail. Cleared automatically at power-on to indicate that the PLL is not correctly tracking the crystal clock. This may be due to the absence of a crystal clock or an external crystal at power-on. In this mode, the PLL output can be 16.78 MHz 20%. Reserved. Should be written with 0. Reserved. Should be written with 0. Fast Interrupt Response Bit. Set by the user enabling the response to any interrupt to be executed at the fastest core clock frequency, regardless of the configuration of the CD2-0 bits (see below). Once user code has returned from an interrupt, the core resumes code execution at the core clock selected by the CD2-0 bits. Cleared by the user to disable the fast interrupt response feature. CPU (Core Clock) Divider Bits. This number determines the frequency at which the microcontroller core operates. Core Clock Frequency (MHz) CD0 CD1 CD2 16.777216 0 0 0 8.388608 1 0 0 4.194304 0 1 0 2.097152 (Default Core Clock Frequency) 1 1 0 1.048576 0 0 1 0.524288 1 0 1 0.262144 0 1 1 0.131072 1 1 1
6
LOCK
5 4 3
------FINT
2 1 0
CD2 CD1 CD0
Rev. 0 | Page 41 of 88
ADuC841/ADuC842/ADuC843
PULSE-WIDTH MODULATOR (PWM)
The PWM on the ADuC841/ADuC842/ADuC843 is a highly flexible PWM offering programmable resolution and an input clock, and can be configured for any one of six different modes of operation. Two of these modes allow the PWM to be configured as a - DAC with up to 16 bits of resolution. A block diagram of the PWM is shown in Figure 47. Note the PWM clock's sources are different for the ADuC841, and are given in Table 17.
fVCO
TO/EXTERNAL PWM CLOCK CLOCK SELECT PROGRAMMABLE DIVIDER
PWMCON, as described in the following sections, controls the different modes of operation of the PWM as well as the PWM clock frequency. PWM0H/L and PWM1H/L are the data registers that determine the duty cycles of the PWM outputs. The output pins that the PWM uses are determined by the CFG841/CFG842 register, and can be either P2.6 and P2.7 or P3.4 and P3.3. In this section of the data sheet, it is assumed that P2.6 and P2.7 are selected as the PWM outputs. To use the PWM user software, first write to PWMCON to select the PWM mode of operation and the PWM input clock. Writing to PWMCON also resets the PWM counter. In any of the 16-bit modes of operation (Modes 1, 3, 4, 6), user software should write to the PWM0L or PWM1L SFRs first. This value is written to a hidden SFR. Writing to the PWM0H or PWM1H SFRs updates both the PWMxH and the PWMxL SFRs but does not change the outputs until the end of the PWM cycle in progress. The values written to these 16-bit registers are then used in the next PWM cycle.
PWMCON PWM Control SFR
fXTAL/15 fXTAL
16-BIT PWM COUNTER
COMPARE
P2.6 P2.7
03260-0-046
MODE
PWM0H/L
PWM1H/L
Figure 47. PWM Block Diagram
SFR Address The PWM uses five SFRs: the control SFR (PWMCON) and four data SFRs (PWM0H, PWM0L, PWM1H, and PWM1L).
Table 17. PWMCON SFR Bit Designations
Bit No. 7 6 5 4 Name SNGL MD2 MD1 MD0
AEH 00H No
Power-On Default Bit Addressable
3 2
CDIV1 CDIV0
1 0
CSEL1 CSEL0
Description Turns off PMW output at P2.6 or P3.4, leaving the port pin free for digital I/O. PWM Mode Bits. The MD2/1/0 bits choose the PWM mode as follows: MD2 MD1 MD0 Mode 0 0 0 Mode 0: PWM Disabled 0 0 1 Mode 1: Single variable resolution PWM on P2.7 or P3.3 0 1 0 Mode 2: Twin 8-bit PWM 0 1 1 Mode 3: Twin 16-bit PWM 1 0 0 Mode 4: Dual NRZ 16-bit - DAC 1 0 1 Mode 5: Dual 8-bit PWM 1 1 0 Mode 6: Dual RZ 16-bit - DAC 1 1 1 Reserved PWM Clock Divider. Scale the clock source for the PWM counter as follows: CDIV1 CDIV0 Description 0 0 PWM Counter = Selected Clock/1 0 1 PWM Counter = Selected Clock/4 1 0 PWM Counter = Selected Clock/16 1 1 PWM Counter = Selected Clock/64 PWM Clock Divider. Select the clock source for the PWM as follows: CSEL1 CSEL0 Description 0 0 PWM Clock = fXTAL/15, ADuC841 = fOCS/DIVIDE FACTOR /15 (see the CFG841 register) 0 1 PWM Clock = fXTAL, ADuC841 = fOCS/DIVIDE FACTOR (see the CFG841 register) 1 0 PWM Clock = External input at P3.4/T0 1 1 PWM Clock = fVCO = 16.777216 MHz, ADuC841 = fOSC
Rev. 0 | Page 42 of 88
ADuC841/ADuC842/ADuC843
PWM Modes of Operation
PWM1L
Mode 0: PWM Disabled
PWM COUNTER PWM0H PWM0L PWM1H 0 P2.6 P2.7
03260-0-048
03260-0-049
The PWM is disabled allowing P2.6 and P2.7 to be used as normal.
Mode 1: Single Variable Resolution PWM
In Mode 1, both the pulse length and the cycle time (period) are programmable in user code, allowing the resolution of the PWM to be variable. PWM1H/L sets the period of the output waveform. Reducing PWM1H/L reduces the resolution of the PWM output but increases the maximum output rate of the PWM. For example, setting PWM1H/L to 65536 gives a 16-bit PWM with a maximum output rate of 266 Hz (16.777 MHz/65536). Setting PWM1H/L to 4096 gives a 12-bit PWM with a maximum output rate of 4096 Hz (16.777 MHz/4096). PWM0H/L sets the duty cycle of the PWM output waveform, as shown in Figure 48.
PWM1H/L PWM COUNTER PWM0H/L
Figure 49. PWM Mode 2
Mode 3: Twin 16-Bit PWM
In Mode 3, the PWM counter is fixed to count from 0 to 65536, giving a fixed 16-bit PWM. Operating from the 16.777 MHz core clock results in a PWM output rate of 256 Hz. The duty cycle of the PWM outputs at P2.6 and P2.7 is independently programmable. As shown in Figure 50, while the PWM counter is less than PWM0H/L, the output of PWM0 (P2.6) is high. Once the PWM counter equals PWM0H/L, PWM0 (P2.6) goes low and remains low until the PWM counter rolls over. Similarly, while the PWM counter is less than PWM1H/L, the output of PWM1 (P2.7) is high. Once the PWM counter equals PWM1H/L, PWM1 (P2.7) goes low and remains low until the PWM counter rolls over. In this mode, both PWM outputs are synchronized, i.e., once the PWM counter rolls over to 0, both PWM0 (P2.6) and PWM1 go high.
65536 PWM COUNTER PWM1H/L
0 P2.7
Figure 48. PWM in Mode 1
Mode 2: Twin 8-Bit PWM
In Mode 2, the duty cycle of the PWM outputs and the resolution of the PWM outputs are both programmable. The maximum resolution of the PWM output is 8 bits. PWM1L sets the period for both PWM outputs. Typically, this is set to 255 (FFH) to give an 8-bit PWM, although it is possible to reduce this as necessary. A value of 100 could be loaded here to give a percentage PWM, i.e., the PWM is accurate to 1%. The outputs of the PWM at P2.6 and P2.7 are shown in Figure 49. As can be seen, the output of PWM0 (P2.6) goes low when the PWM counter equals PWM0L. The output of PWM1 (P2.7) goes high when the PWM counter equals PWM1H and goes low again when the PWM counter equals PWM0H. Setting PWM1H to 0 ensures that both PWM outputs start simultaneously.
03260-0-047
PWM0H/L 0 P2.6
P2.7
Figure 50. PWM Mode 3
Rev. 0 | Page 43 of 88
ADuC841/ADuC842/ADuC843
Mode 4: Dual NRZ 16-Bit - DAC
PWM COUNTERS PWM1L
P2.7
For example, if PWM1H is set to 4010H (slightly above one quarter of FS), then typically P2.7 will be low for three clocks and high for one clock (each clock is approximately 60 ns). Over every 65536 clocks, the PWM compensates for the fact that the output should be slightly above one quarter of full scale by having a high cycle followed by only two low cycles.
PWM0H/L = C000H CARRY OUT AT P1.0 16-BIT 0 1 1 1 0 1 1
Figure 52. PWM Mode 5
Mode 6: Dual RZ 16-Bit - DAC
60s 16-BIT 16-BIT
Mode 6 provides a high speed PWM output similar to that of a - DAC. Mode 6 operates very similarly to Mode 4. However, the key difference is that Mode 6 provides return-to-zero (RZ) - DAC output. Mode 4 provides non-return-to-zero - DAC outputs. The RZ mode ensures that any difference in the rise and fall times will not affect the - DAC INL. However, the RZ mode halves the dynamic range of the - DAC outputs from 0 V-AVDD down to 0 V-AVDD/2. For best results, this mode should be used with a PWM clock divider of 4. If PWM1H is set to 4010H (slightly above one quarter of FS), typically P2.7 will be low for three full clocks (3 x 60 ns), high for half a clock (30 ns), and then low again for half a clock (30 ns) before repeating itself. Over every 65536 clocks, the PWM will compensate for the fact that the output should be slightly above one quarter of full scale by leaving the output high for two half clocks in four. The rate at which this happens depends on the value and degree of compensation required.
16.777MHz
LATCH
16-BIT
16-BIT 0 0 0 0 0 0
1
CARRY OUT AT P2.7
16-BIT 60s PWM1H/L = 4000H
03260-0-050
Figure 51. PWM Mode 4
PWM0H/L = C000H CARRY OUT AT P2.6 16-BIT 01 1 1 01 1
For faster DAC outputs (at lower resolution), write 0s to the LSBs that are not required. If, for example, only 12-bit performance is required, write 0s to the four LSBs. This means that a 12-bit accurate - DAC output can occur at 4.096 kHz. Similarly writing 0s to the 8 LSBs gives an 8-bit accurate - DAC output at 65 kHz.
Mode 5: Dual 8-Bit PWM
240s 16-BIT 16-BIT
4MHz
LATCH
PWM1H/L = 4000H
Figure 53. PWM Mode 6
Rev. 0 | Page 44 of 88
03260-0-052
In Mode 5, the duty cycle of the PWM outputs and the resolution of the PWM outputs are individually programmable. The maximum resolution of the PWM output is 8 bits. The output resolution is set by the PWM1L and PWM1H SFRs for the P2.6 and P2.7 outputs, respectively. PWM0L and PWM0H sets the duty cycles of the PWM outputs at P2.6 and P2.7, respectively. Both PWMs have the same clock source and clock divider.
16-BIT
16-BIT
0 0, 3/4, 1/2, 1/4, 0 16-BIT 240s
0
01
0
0
03260-0-051
Mode 4 provides a high speed PWM output similar to that of a - DAC. Typically, this mode is used with the PWM clock equal to 16.777216 MHz. In this mode, P2.6 and P2.7 are updated every PWM clock (60 ns in the case of 16 MHz). Over any 65536 cycles (16-bit PWM) PWM0 (P2.6) is high for PWM0H/L cycles and low for (65536 - PWM0H/L) cycles. Similarly, PWM1 (P2.7) is high for PWM1H/L cycles and low for (65536 - PWM1H/L) cycles.
PWM1H PWM0L PWM0H 0 P2.6
0
CARRY OUT AT P2.7
ADuC841/ADuC842/ADuC843
SERIAL PERIPHERAL INTERFACE (SPI)
The ADuC841/ADuC842/ADuC843 integrate a complete hardware serial peripheral interface on-chip. SPI is an industrystandard synchronous serial interface that allows 8 bits of data to be synchronously transmitted and received simultaneously, i.e., full duplex. Note that the SPI pins are shared with the I2C pins. Therefore, the user can enable only one interface or the other on these pins at any given time (see SPE in Table 18). SPI can be operated at the same time as the I2C interface if the MSPI bit in CFG841/CFG8842 is set. This moves the SPI outputs (MISO, MOSI, and SCLOCK) to P3.3, P3.4, and P3.5, respectively). The SPI port can be configured for master or slave operation and typically consists of four pins, described in the following sections.
SCLOCK (Serial Clock I/O Pin)
The master serial clock (SCLOCK) is used to synchronize the data being transmitted and received through the MOSI and MISO data lines. A single data bit is transmitted and received in each SCLOCK period. Therefore, a byte is transmitted/received after eight SCLOCK periods. The SCLOCK pin is configured as an output in master mode and as an input in slave mode. In master mode, the bit rate, polarity, and phase of the clock are controlled by the CPOL, CPHA, SPR0, and SPR1 bits in the SPICON SFR (see Table 18). In slave mode, the SPICON register must be configured with the phase and polarity (CPHA and CPOL) of the expected input clock. In both master and slave modes, the data is transmitted on one edge of the SCLOCK signal and sampled on the other. It is important, therefore, that CPHA and CPOL are configured the same for the master and slave devices.
MISO (Master In, Slave Out Data I/O Pin)
The MISO pin is configured as an input line in master mode and as an output line in slave mode. The MISO line on the master (data in) should be connected to the MISO line in the slave device (data out). The data is transferred as byte-wide (8-bit) serial data, MSB first.
SS (Slave Select Input Pin)
The SS pin is shared with the ADC5 input. To configure this pin as a digital input, the bit must be cleared, e.g., CLR P1.5. This line is active low. Data is received or transmitted in slave mode only when the SS pin is low, allowing the parts to be used in single-master, multislave SPI configurations. If CPHA = 1, the SS input may be permanently pulled low. If CPHA = 0, the SS input must be driven low before the first bit in a byte-wide transmission or reception and return high again after the last bit in that byte-wide transmission or reception. In SPI slave mode, the logic level on the external SS pin can be read via the SPR0 bit in the SPICON SFR. The SFR registers, described in the following tables, are used to control the SPI interface.
MOSI (Master Out, Slave In Pin)
The MOSI pin is configured as an output line in master mode and as an input line in slave mode. The MOSI line on the master (data out) should be connected to the MOSI line in the slave device (data in). The data is transferred as byte-wide (8-bit) serial data, MSB first.
Rev. 0 | Page 45 of 88
ADuC841/ADuC842/ADuC843
SPICON SPI Control Register
SFR Address Power-On Default Bit Addressable
F8H 04H Yes
Table 18. SPICON SFR Bit Designations
Bit No. 7 Name ISPI Description SPI Interrupt Bit. Set by the MicroConverter at the end of each SPI transfer. Cleared directly by user code or indirectly by reading the SPIDAT SFR. Write Collision Error Bit. Set by the MicroConverter if SPIDAT is written to while an SPI transfer is in progress. Cleared by user code. SPI Interface Enable Bit. Set by the user to enable the SPI interface. Cleared by the user to enable the I2C pins, this is not requiredto enable the I2C interface if the MSPI bit is set in CFG841/CFG842. In this case, the I2C interface is automatically enabled. SPI Master/Slave Mode Select Bit. Set by the user to enable master mode operation (SCLOCK is an output). Cleared by the user to enable slave mode operation (SCLOCK is an input). Clock Polarity Select Bit. Set by the user if SCLOCK idles high. Cleared by the user if SCLOCK idles low. Clock Phase Select Bit. Set by the user if leading SCLOCK edge is to transmit data. Cleared by the user if trailing SCLOCK edge is to transmit data. SPI Bit Rate Select Bits. These bits select the SCLOCK rate (bit rate) in master mode as follows: SPR1 SPR0 Selected Bit Rate 0 0 fOSC/2 0 1 fOSC/4 1 0 fOSC/8 1 1 fOSC/16 In SPI slave mode, i.e., SPIM = 0, the logic level on the external SS pin can be read via the SPR0 bit.
6
WCOL
5
SPE
4
SPIM
3
CPOL1
2
CPHA1
1 0
SPR1 SPR0
1
The CPOL and CPHA bits should both contain the same values for master and slave devices.
SPIDAT Function
SFR Address Power-On Default Bit Addressable
SPI Data Register SPIDAT SFR is written by the user to transmit data over the SPI interface or read by user code to read data just received by the SPI interface. F7H 00H No
Rev. 0 | Page 46 of 88
ADuC841/ADuC842/ADuC843
Using the SPI Interface
Depending on the configuration of the bits in the SPICON SFR shown in Table 18, the ADuC841/ADuC842/ADuC843 SPI interface transmits or receives data in a number of possible modes. Figure 54 shows all possible SPI configurations for the parts, and the timing relationships and synchronization between the signals involved. Also shown in this figure is the SPI interrupt bit (ISPI) and how it is triggered at the end of each byte-wide communication.
SCLOCK (CPOL = 1)
In master mode, a byte transmission or reception is initiated by a write to SPIDAT. Eight clock periods are generated via the SCLOCK pin and the SPIDAT byte being transmitted via MOSI. With each SCLOCK period, a data bit is also sampled via MISO. After eight clocks, the transmitted byte will be completely transmitted, and the input byte will be waiting in the input shift register. The ISPI flag will be set automatically, and an interrupt will occur if enabled. The value in the shift register will be latched into SPIDAT.
SPI Interface--Slave Mode
In slave mode, SCLOCK is an input. The SS pin must also be driven low externally during the byte communication. Transmission is also initiated by a write to SPIDAT. In slave mode, a data bit is transmitted via MISO, and a data bit is received via MOSI through each input SCLOCK period. After eight clocks, the transmitted byte will be completely transmitted, and the input byte will be waiting in the input shift register. The ISPI flag will be set automatically, and an interrupt will occur if enabled. The value in the shift register will be latched into SPIDAT only when the transmission/reception of a byte has been completed. The end of transmission occurs after the eighth clock has been received if CPHA = 1, or when SS returns high if CPHA = 0.
SCLOCK (CPOL = 0) SS
SAMPLE INPUT
(CPHA = 1)
DATA OUTPUT
? MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB
ISPI FLAG
SAMPLE INPUT
DATA OUTPUT (CPHA = 0)
MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB ?
03260-0-053
ISPI FLAG
Figure 54. SPI Timing, All Modes
SPI Interface--Master Mode
In master mode, the SCLOCK pin is always an output and generates a burst of eight clocks whenever user code writes to the SPIDAT register. The SCLOCK bit rate is determined by SPR0 and SPR1 in SPICON. Also note that the SS pin is not used in master mode. If the parts need to assert the SS pin on an external slave device, a port digital output pin should be used.
Rev. 0 | Page 47 of 88
ADuC841/ADuC842/ADuC843
I2C COMPATIBLE INTERFACE
The ADuC841/ADuC842/ADuC843 support a fully licensed I2C serial interface. The I2C interface is implemented as a full hardware slave and software master. SDATA is the data I/O pin, and SCLOCK is the serial clock. These two pins are shared with the MOSI and SCLOCK pins of the on-chip SPI interface. To enable the I2C interface, the SPI interface must be turned off (see SPE in Table 18) or the SPI interface must be moved to P3.3, P3.4, and P3.5 via the CFG841.1/CFG842.1 bit. Application Note uC001 describes the operation of this interface as implemented and is available from the MicroConverter website at www.analog.com/microconverter.
Table 19. I2CCON SFR Bit Designations, Master Mode
Bit No. 7 Name MDO Description I2C Software Master Data Output Bit (Master Mode Only). This data bit is used to implement a master I2C transmitter interface in software. Data written to this bit is output on the SDATA pin if the data output enable (MDE) bit is set. I2C Software Master Data Output Enable Bit (Master Mode Only). Set by the user to enable the SDATA pin as an output (Tx). Cleared by the user to enable the SDATA pin as an input (Rx). I2C Software Master Clock Output Bit (Master Mode Only). This data bit is used to implement a master I2C transmitter interface in software. Data written to this bit is output on the SCLOCK pin. I2C Software Master Data Input Bit (Master Mode Only). This data bit is used to implement a master I2C receiver interface in software. Data on the SDATA pin is latched into this bit on SCLOCK if the data output enable (MDE) bit is 0. I2C Master/Slave Mode Bit. Set by the user to enable I2C software master mode. Cleared by the user to enable I2C hardware slave mode. Reserved. Reserved. Reserved.
Three SFRs are used to control the I2C interface and are described in the following tables.
I2CCON I2C Control Register
SFR Address Power-On Default Bit Addressable
E8H 00H Yes
6
MDE
5
MCO
4
MDI
3
I2CM
2 1 0
----------
Table 20. I2CCON SFR Bit Designations, Slave Mode
Bit No. 7 Name I2CSI Description I2C Stop Interrupt Enable Bit. Set by the user to enable I2C stop interrupts. If set, a stop bit that follows a valid start condition generates an interrupt. Cleared by the user to disable I2C stop interrupts. I2C General Call Status Bit. Set by hardware after receiving a general call address. Cleared by the user. I2C Interrupt Decode Bits. Set by hardware to indicate the source of an I2C interrupt. 00 Start and Matching Address. 01 Repeated Start and Matching Address. 10 User Data. 11 Stop after a Start and Matching Address. I2C Master/Slave Mode Bit. Set by the user to enable I2C software master mode. Cleared by the user to enable I2C hardware slave mode.
6
I2CGC
5 4
I2CID1 I2CID0
3
I2CM
Rev. 0 | Page 48 of 88
ADuC841/ADuC842/ADuC843
Bit No. 2 Name I2CRS Description I2C Reset Bit (Slave Mode Only). Set by the user to reset the I2C interface. Cleared by the user code for normal I2C operation. I2C Direction Transfer Bit (Slave Mode Only). Set by the MicroConverter if the interface is transmitting. Cleared by the MicroConverter if the interface is receiving. I2C Interrupt Bit (Slave Mode Only). Set by the MicroConverter after a byte has been transmitted or received. Cleared automatically when user code reads the I2CDAT SFR (see I2CDAT below).
1
I2CTX
0
I2CI
I2CADD
I2C Address Register
Function
Holds the first I2C peripheral address for the part. It may be overwritten by user code. Application Note uC001 at www.analog.com/microconverter describes the format of the I2C standard 7-bit address in detail. 9BH 55H No
I2C Address Register
SFR Address Power-On Default Bit Addressable
I2CADD1
Function SFR Address Power-On Default Bit Addressable
I2CADD2
Holds the second I2C peripheral address for the part. It may be overwritten by user code. 91H 7FH No
I2C Address Register
Function SFR Address Power-On Default Bit Addressable
I2CADD3
Holds the third I2C peripheral address for the part. It may be overwritten by user code. 92H 7FH No
I2C Address Register
Function SFR Address Power-On Default Bit Addressable
I2CDAT
Holds the fourth I2C peripheral address for the part. It may be overwritten by user code. 93H 7FH No
I2C Data Register
Function
Written by the user to transmit data over the I2C interface or read by user code to read data just received by the I2C interface. Accessing I2CDAT automatically clears any pending I2C interrupt and the I2CI bit in the I2CCON SFR. User software should access I2CDAT only once per interrupt cycle. 9AH 00H No
SFR Address Power-On Default Bit Addressable
The main features of the MicroConverter I2C interface are * * Only two bus lines are required: a serial data line (SDATA) and a serial clock line (SCLOCK). An I2C master can communicate with multiple slave devices. Because each slave device has a unique 7-bit address, single master/slave relationships can exist at all times even in a multislave environment. Ability to respond to four separate addresses when operating in slave mode.
*
Rev. 0 | Page 49 of 88
ADuC841/ADuC842/ADuC843
* An I2C slave can respond to repeated start conditions without a stop bit in between. This allows a master to change direction of transfer without giving up the bus. Note that the repeated start is detected only when a slave has previously been configured as a receiver. On-chip filtering rejects <50 ns spikes on the SDATA and the SCLOCK lines to preserve data integrity.
DVDD
*
Once enabled in I2C slave mode, the slave controller waits for a start condition. If the part detects a valid start condition, followed by a valid address, followed by the R/W bit, the I2CI interrupt bit is automatically set by hardware. The I2C peripheral generates a core interrupt only if the user has pre-configured the I2C interrupt enable bit in the IEIP2 SFR as well as the global interrupt bit, EA, in the IE SFR. i.e.,
;Enabling I2C Interrupts for the ADuC842 MOV IEIP2,#01h ; enable I2C interrupt SETB EA
I2C MASTER
I2C SLAVE 1
An autoclear of the I2CI bit is implemented on the parts so that this bit is cleared automatically on a read or write access to the I2CDAT SFR.
03260-0-054
I2C SLAVE 2
MOV I2CDAT, A MOV A, I2CDAT
; I2CI auto-cleared ; I2CI auto-cleared
Figure 55. Typical I2C System
Software Master Mode
The ADuC841/ADuC842/ADuC843 can be used as I2C master devices by configuring the I2C peripheral in master mode and writing software to output the data bit by bit. This is referred to as a software master. Master mode is enabled by setting the I2CM bit in the I2CCON register. To transmit data on the SDATA line, MDE must be set to enable the output driver on the SDATA pin. If MDE is set, the SDATA pin is pulled high or low depending on whether the MDO bit is set or cleared. MCO controls the SCLOCK pin and is always configured as an output in master mode. In master mode, the SCLOCK pin is pulled high or low depending on the whether MCO is set or cleared. To receive data, MDE must be cleared to disable the output driver on SDATA. Software must provide the clocks by toggling the MCO bit and reading the SDATA pin via the MDI bit. If MDE is cleared, MDI can be used to read the SDATA pin. The value of the SDATA pin is latched into MDI on a rising edge of SCLOCK. MDI is set if the SDATA pin was high on the last rising edge of SCLOCK. MDI is clear if the SDATA pin was low on the last rising edge of SCLOCK. Software must control MDO, MCO, and MDE appropriately to generate the start condition, slave address, acknowledge bits, data bytes, and stop conditions. These functions are described in Application Note uC001.
If for any reason the user tries to clear the interrupt more than once, i.e., access the data SFR more than once per interrupt, then the I2C controller will halt. The interface will then have to be reset using the I2CRS bit. The user can choose to poll the I2CI bit or to enable the interrupt. In the case of the interrupt, the PC counter vectors to 003BH at the end of each complete byte. For the first byte, when the user gets to the I2CI ISR, the 7-bit address and the R/W bit appear in the I2CDAT SFR. The I2CTX bit contains the R/W bit sent from the master. If I2CTX is set, the master is ready to receive a byte. Therefore the slave will transmit data by writing to the I2CDAT register. If I2CTX is cleared, the master is ready to transmit a byte. Therefore the slave will receive a serial byte. Software can interrogate the state of I2CTX to determine whether it should write to or read from I2CDAT. Once the part has received a valid address, hardware holds SCLOCK low until the I2CI bit is cleared by software. This allows the master to wait for the slave to be ready before transmitting the clocks for the next byte. The I2CI interrupt bit is set every time a complete data byte is received or transmitted, provided it is followed by a valid ACK. If the byte is followed by a NACK, an interrupt is not generated. The part continues to issue interrupts for each complete data byte transferred until a stop condition is received or the interface is reset. When a stop condition is received, the interface resets to a state in which it is waiting to be addressed (idle). Similarly, if the interface receives a NACK at the end of a sequence, it also returns to the default idle state. The I2CRS bit can be used to reset the I2C interface. This bit can be used to force the interface back to the default idle state.
Hardware Slave Mode
After reset, the ADuC841/ADuC842/ADuC843 default to hardware slave mode. The I2C interface is enabled by clearing the SPE bit in SPICON (this is not necessary if the MSPI bit is set). Slave mode is enabled by clearing the I2CM bit in I2CCON. The parts have a full hardware slave. In slave mode, the I2C address is stored in the I2CADD register. Data received or to be transmitted is stored in the I2CDAT register.
Rev. 0 | Page 50 of 88
ADuC841/ADuC842/ADuC843
DUAL DATA POINTER
The ADuC841/ADuC842/ADuC843 incorporate two data pointers. The second data pointer is a shadow data pointer and is selected via the data pointer control SFR (DPCON). DPCON also includes some useful features such as automatic hardware post-increment and post-decrement as well as automatic data pointer toggle. DPCON is described in Table 21.
DPCON Data Pointer Control SFR
SFR Address Power-On Default Bit Addressable
A7H 00H No
Table 21. DPCON SFR Bit Designations
Bit No. 7 6 Name ---DPT Description Reserved. Data Pointer Automatic Toggle Enable. Cleared by the user to disable autoswapping of the DPTR. Set in user software to enable automatic toggling of the DPTR after each each MOVX or MOVC instruction. Shadow Data Pointer Mode. These two bits enable extra modes of the shadow data pointer's operation, allowing for more compact and more efficient code size and execution. Behavior of the shadow data pointer. 8052 behavior. DPTR is post-incremented after a MOVX or a MOVC instruction. DPTR is post-decremented after a MOVX or MOVC instruction. DPTR LSB is toggled after a MOVX or MOVC instruction. (This instruction can be useful for moving 8-bit blocks to/from 16-bit devices.) Main Data Pointer Mode. These two bits enable extra modes of the main data pointer operation, allowing for more compact and more efficient code size and execution. Behavior of the main data pointer. 8052 behavior. DPTR is post-incremented after a MOVX or a MOVC instruction. DPTR is post-decremented after a MOVX or MOVC instruction. DPTR LSB is toggled after a MOVX or MOVC instruction. (This instruction can be useful for moving 8-bit blocks to/from 16-bit devices.) This bit is not implemented to allow the INC DPCON instruction toggle the data pointer without incrementing the rest of the SFR. Data Pointer Select. Cleared by the user to select the main data pointer. This means that the contents of this 24-bit register are placed into the three SFRs: DPL, DPH, and DPP. Set by the user to select the shadow data pointer. This means that the contents of a separate 24-bit register appears in the three SFRs: DPL, DPH, and DPP.
MOV DPTR,#0 MOV DPCON,#55H ; ; ; ; ; ; ; ; ; ; ; ; Main DPTR = 0 Select shadow DPTR DPTR1 increment mode, DPTR0 increment mode DPTR auto toggling ON Shadow DPTR = D000H Get data Post Inc DPTR Swap to Main DPTR (Data) Put ACC in XRAM Increment main DPTR Swap Shadow DPTR (Code)
5 4
DP1m1 DP1m0
m1 0 0 1 1
m0 0 1 0 1
3 2
DP0m1 DP0m0
m1 0 0 1 1
m0 0 1 0 1
1 0
---DPSEL
Note 1: This is the only place where the main and shadow data pointers are distinguished. Everywhere else in this data sheet wherever the DPTR is mentioned, operation on the active DPTR is implied. Note 2: Only MOVC/MOVX @DPTR instructions are relevant above. MOVC/MOVX PC/@Ri instructions do not cause the DPTR to automatically post increment/decrement, and so on. To illustrate the operation of DPCON, the following code copies 256 bytes of code memory at address D000H into XRAM starting from Address 0000H.
MOV DPTR,#0D000H MOVELOOP: CLR A MOVC A,@A+DPTR MOVX @DPTR,A MOV A, DPL JNZ MOVELOOP
Rev. 0 | Page 51 of 88
ADuC841/ADuC842/ADuC843
POWER SUPPLY MONITOR
As its name suggests, the power supply monitor, once enabled, monitors the DVDD supply on the ADuC841/ADuC842/ ADuC843. It indicates when any of the supply pins drops below one of two user selectable voltage trip points, 2.93 V and 3.08 V. For correct operation of the power supply monitor function, AVDD must be equal to or greater than 2.7 V. Monitor function is controlled via the PSMCON SFR. If enabled via the IEIP2 SFR, the monitor interrupts the core using the PSMI bit in the PSMCON SFR. This bit is not cleared until the failing power supply has returned above the trip point for at least 250 ms. This monitor function allows the user to save working registers to avoid possible data loss due to the low supply condition, and also ensures that normal code execution does not resume until a safe supply level has been well established. The supply monitor
Table 22. PSMCON SFR Bit Designations
Bit No. 7 6 Name ---CMPD Description Reserved. DVDD Comparator Bit. This is a read-only bit that directly reflects the state of the DVDD comparator. Read 1 indicates that the DVDD supply is above its selected trip point. Read 0 indicates that the DVDD supply is below its selected trip point. Power Supply Monitor Interrupt Bit. This bit is set high by the MicroConverter if either CMPA or CMPD is low, indicating low analog or digital supply. The PSMI bit can be used to interrupt the processor. Once CMPD and/or CMPA return (and remain) high, a 250 ms counter is started. When this counter times out, the PSMI interrupt is cleared. PSMI can also be written by the user. However, if either comparator output is low, it is not possible for the user to clear PSMI. DVDD Trip Point Selection Bits. These bits select the DVDD trip point voltage as follows: TPD1 TPD0 Selected DVDD Trip Point (V) 0 0 Reserved 0 1 3.08 1 0 2.93 1 1 Reserved Reserved. Reserved. Power Supply Monitor Enable Bit. Set to 1 by the user to enable the power supply monitor circuit. Cleared to 0 by the user to disable the power supply monitor circuit.
is also protected against spurious glitches triggering the interrupt circuit. Note that the 5 V part has an internal POR trip level of 4.5 V, which means that there are no usable PSM levels on the 5 V part. The 3 V part has a POR trip level of 2.45 V, allowing all PSM trip points to be used.
PSMCON Power Supply Monitor Control Register
SFR Address Power-On Default Bit Addressable
DFH DEH No
5
PSMI
4 3
TPD1 TPD0
2 1 0
------PSMEN
Rev. 0 | Page 52 of 88
ADuC841/ADuC842/ADuC843
WATCHDOG TIMER
The purpose of the watchdog timer is to generate a device reset or interrupt within a reasonable amount of time if the ADuC841/ ADuC842/ADuC843 enter an erroneous state, possibly due to a programming error or electrical noise. The watchdog function can be disabled by clearing the WDE (watchdog enable) bit in the watchdog control (WDCON) SFR. When enabled, the watchdog circuit generates a system reset or interrupt (WDS) if the user program fails to set the watchdog (WDE) bit within a predetermined amount of time (see PRE3-0 bits in Table 23. The watchdog timer is clocked directly from the 32 kHz external crystal on the ADuC842/ADuC843. On the ADuC841,
Table 23. WDCON SFR Bit Designations
Bit No. 7 6 5 4 Name PRE3 PRE2 PRE1 PRE0 Description Watchdog Timer Prescale Bits. The watchdog timeout period is given by the equation tWD = (2PRE x (29/ fXTAL)) (0 - PRE - 7; fXTAL = 32.768 kHz (ADuC842/ADuC843), or 32kHz 10%(ADuC841) ) PRE3 PRE2 PRE1 PRE0 Timeout Period (ms) Action 0 0 0 0 15.6 Reset or Interrupt 0 0 0 1 31.2 Reset or Interrupt 0 0 1 0 62.5 Reset or Interrupt 0 0 1 1 125 Reset or Interrupt 0 1 0 0 250 Reset or Interrupt 0 1 0 1 500 Reset or Interrupt 0 1 1 0 1000 Reset or Interrupt 0 1 1 1 2000 Reset or Interrupt 1 0 0 0 0.0 Immediate Reset PRE3-0 > 1000 Reserved Watchdog Interrupt Response Enable Bit. If this bit is set by the user, the watchdog generates an interrupt response instead of a system reset when the watchdog timeout period has expired. This interrupt is not disabled by the CLR EA instruction, and it is also a fixed, high priority interrupt. If the watchdog is not being used to monitor the system, it can be used alternatively as a timer. The prescaler is used to set the timeout period in which an interrupt will be generated. Watchdog Status Bit. Set by the watchdog controller to indicate that a watchdog timeout has occurred. Cleared by writing a 0 or by an external hardware reset. It is not cleared by a watchdog reset. Watchdog Enable Bit. Set by the user to enable the watchdog and clear its counters. If this bit is not set by the user within the watchdog timeout period, the watchdog generates a reset or interrupt, depending on WDIR. Cleared under the following conditions: user writes 0, watchdog reset (WDIR = 0); hardware reset; PSM interrupt. Watchdog Write Enable Bit. To write data to the WDCON SFR involves a double instruction sequence. The WDWR bit must be set and the very next instruction must be a write instruction to the WDCON SFR. For example:
CLR SETB MOV SETB EA WDWR WDCON,#72H EA ;disable interrupts while writing ;to WDT ;allow write to WDCON ;enable WDT for 2.0s timeout ;enable interrupts again (if rqd)
the watchdog timer is clocked by an internal R/C oscillator at 32 kHz 10%. The WDCON SFR can be written only by user software if the double write sequence described in WDWR below is initiated on every write access to the WDCON SFR.
WDCON Watchdog Timer Control Register
SFR Address Power-On Default Bit Addressable
C0H 10H Yes
3
WDIR
2
WDS
1
WDE
0
WDWR
Rev. 0 | Page 53 of 88
ADuC841/ADuC842/ADuC843
TIME INTERVAL COUNTER (TIC)
A TIC is provided on-chip for counting longer intervals than the standard 8051 compatible timers are capable of. The TIC is capable of timeout intervals ranging from 1/128 second to 255 hours. Furthermore, this counter is clocked by the external 32.768 kHz crystal rather than by the core clock, and it has the ability to remain active in power-down mode and time long power-down intervals. This has obvious applications for remote battery-powered sensors where regular widely spaced readings are required. Six SFRs are associated with the time interval counter, TIMECON being its control register. Depending on the configuration of the IT0 and IT1 bits in TIMECON, the selected time counter register overflow clocks the interval counter. When this counter is equal to the time interval value loaded in the INTVAL SFR, the TII bit (TIMECON.2) is set and generates an interrupt if enabled. If the part is in power-down mode, again with TIC interrupt enabled, the TII bit wakes up the device and resumes code execution by vectoring directly to the TIC interrupt service vector address at 0053H. The TIC-related SFRs are described in Table 24. Note also that the time based SFRs can be written initially with the current time; the TIC can then be controlled and accessed by user software. In effect, this facilitates the implementation of a real-time clock. A block diagram of the TIC is shown in Figure 56. The TIC is clocked directly from a 32 kHz external crystal on the ADuC842/ADuC843 and by the internal 32 kHz 10% R/C oscillator on the ADuC841. Due to this, instructions that access the TIC registers will also be clocked at this speed. The user should ensure that there is sufficient time between instructions to these registers to allow them to execute correctly.
TCEN 32.768kHz EXTERNAL CRYSTAL ITS0, 1
8-BIT PRESCALER
HUNDREDTHS COUNTER HTHSEC INTERVAL TIMEBASE SELECTION MUX TIEN
SECOND COUNTER SEC
MINUTE COUNTER MIN
HOUR COUNTER HOUR
8-BIT INTERVAL COUNTER
03260-0-055
INTERVAL TIMEOUT TIME INTERVAL COUNTER INTERRUPT
COMPARE COUNT = INTVAL
TIMER INTVAL INTVAL
Figure 56. TIC, Simplified Block Diagram
Rev. 0 | Page 54 of 88
ADuC841/ADuC842/ADuC843
TIMECON TIC Control Register
SFR Address Power-On Default Bit Addressable
A1H 00H No
Table 24. TIMECON SFR Bit Designations
Bit No. 7 6 Name ---TFH Description Reserved. Twenty-Four Hour Select Bit. Set by the user to enable the hour counter to count from 0 to 23. Cleared by the user to enable the hour counter to count from 0 to 255. Interval Timebase Selection Bits. Written by user to determine the interval counter update rate. ITS1 ITS0 Interval Timebase 0 0 1/128 Second 0 1 Seconds 1 0 Minutes 1 1 Hours Single Time Interval Bit. Set by the user to generate a single interval timeout. If set, a timeout clears the TIEN bit. Cleared by the user to allow the interval counter to be automatically reloaded and start counting again at each interval timeout. TIC Interrupt Bit. Set when the 8-bit interval counter matches the value in the INTVAL SFR. Cleared by user software. Time Interval Enable Bit. Set by the user to enable the 8-bit time interval counter. Cleared by the user to disable the interval counter. Time Clock Enable Bit. Set by the user to enable the time clock to the time interval counters. Cleared by the user to disable the clock to the time interval counters and reset the time interval SFRs to the last value written to them by the user. The time registers (HTHSEC, SEC, MIN, and HOUR) can be written while TCEN is low.
5 4
ITS1 ITS0
3
STI
2
TII
1
TIEN
0
TCEN
Rev. 0 | Page 55 of 88
ADuC841/ADuC842/ADuC843
INTVAL Function User Time Interval Select Register User code writes the required time interval to this register. When the 8-bit interval counter is equal to the time interval value loaded in the INTVAL SFR, the TII bit (TIMECON.2) is set and generates an interrupt if enabled.
SFR Address Power-On Default Bit Addressable Valid Value
A6H 00H No 0 to 255 decimal
HTHSEC Function
SFR Address Power-On Default Bit Addressable Valid Value
Hundredths Seconds Time Register This register is incremented in 1/128 second intervals once TCEN in TIMECON is active. The HTHSEC SFR counts from 0 to 127 before rolling over to increment the SEC time register. A2H 00H No 0 to 127 decimal
SEC Function
SFR Address Power-On Default Bit Addressable Valid Value
Seconds Time Register This register is incremented in 1-second intervals once TCEN in TIMECON is active. The SEC SFR counts from 0 to 59 before rolling over to increment the MIN time register. A3H 00H No 0 to 59 decimal
MIN Function
SFR Address Power-On Default Bit Addressable Valid Value
Minutes Time Register This register is incremented in 1-minute intervals once TCEN in TIMECON is active. The MIN SFR counts from 0 to 59 before rolling over to increment the HOUR time register. A4H 00H No 0 to 59 decimal
HOUR
Hours Time Register
Function SFR Address Power-On Default Bit Addressable Valid Value
This register is incremented in 1-hour intervals once TCEN in TIMECON is active. The HOUR SFR counts from 0 to 23 before rolling over to 0. A5H 00H No 0 to 23 decimal
Rev. 0 | Page 56 of 88
ADuC841/ADuC842/ADuC843
8052 COMPATIBLE ON-CHIP PERIPHERALS
This section gives a brief overview of the various secondary peripheral circuits that are also available to the user on-chip. These remaining functions are mostly 8052 compatible (with a few additional features) and are controlled via standard 8052 SFR bit definitions. In general-purpose I/O port mode, Port 0 pins that have 1s written to them via the Port 0 SFR are configured as open-drain and will therefore float. In this state, Port 0 pins can be used as high impedance inputs. This is represented in Figure 57 by the NAND gate whose output remains high as long as the control signal is low, thereby disabling the top FET. External pull-up resistors are therefore required when Port 0 pins are used as general-purpose outputs. Port 0 pins with 0s written to them drive a logic low output voltage (VOL) and are capable of sinking 1.6 mA.
Parallel I/O
The ADuC841/ADuC842/ADuC843 use four input/output ports to exchange data with external devices. In addition to performing general-purpose I/O, some ports are capable of external memory operations while others are multiplexed with alternate functions for the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general-purpose I/O pin.
Port 1
Port 1 is also an 8-bit port directly controlled via the P1 SFR. Port 1 digital output capability is not supported on this device. Port 1 pins can be configured as digital inputs or analog inputs. By (power-on) default, these pins are configured as analog inputs, i.e., 1 written in the corresponding Port 1 register bit. To configure any of these pins as digital inputs, the user should write a 0 to these port bits to configure the corresponding pin as a high impedance digital input. These pins also have various secondary functions as described in Table 25.
Table 25. Port 1 Alternate Pin Functions
Pin No. P1.0 P1.1 P1.5 Alternate Function T2 (Timer/Counter 2 External Input) T2EX (Timer/Counter 2 Capture/Reload Trigger) SS (Slave Select for the SPI Interface)
Port 0
Port 0 is an 8-bit open-drain bidirectional I/O port that is directly controlled via the Port 0 SFR. Port 0 is also the multiplexed low order address and data bus during accesses to external program or data memory. Figure 57 shows a typical bit latch and I/O buffer for a Port 0 port pin. The bit latch (one bit in the port's SFR) is represented as a Type D flip-flop, which clocks in a value from the internal bus in response to a write to latch signal from the CPU. The Q output of the flip-flop is placed on the internal bus in response to a read latch signal from the CPU. The level of the port pin itself is placed on the internal bus in response to a read pin signal from the CPU. Some instructions that read a port activate the read latch signal, and others activate the read pin signal. See the Read-Modify-Write Instructions section for details.
ADDR/DATA READ LATCH CONTROL DVDD
READ LATCH INTERNAL BUS WRITE TO LATCH READ PIN D CL Q Q P1.x PIN
03260-0-057
LATCH TO ADC
INTERNAL BUS WRITE TO LATCH READ PIN
P0.x PIN D Q
Figure 58. Port 1 Bit Latch and I/O Buffer
03260-0-056
CL Q LATCH
Port 2
Port 2 is a bidirectional port with internal pull-up resistors directly controlled via the P2 SFR. Port 2 also emits the highorder address bytes during fetches from external program memory, and middle and high order address bytes during accesses to the 24-bit external data memory space. As shown in Figure 59, the output drivers of Port 2 are switchable to an internal ADDR and ADDR/DATA bus by an internal control signal for use in external memory accesses (as for Port 0). In external memory addressing mode (CONTROL = 1), the port pins feature push-pull operation controlled by the internal address bus (ADDR line). However, unlike the P0 SFR during external memory accesses, the P2 SFR remains unchanged.
Figure 57. Port 0 Bit Latch and I/O Buffer
As shown in Figure 57, the output drivers of Port 0 pins are switchable to an internal ADDR and ADDR/DATA bus by an internal control signal for use in external memory accesses. During external memory accesses, the P0 SFR has 1s written to it, i.e., all of its bit latches become 1. When accessing external memory, the control signal in Figure 57 goes high, enabling push-pull operation of the output pin from the internal address or data bus (ADDR/DATA line). Therefore, no external pull-ups are required on Port 0 for it to access external memory.
Rev. 0 | Page 57 of 88
ADuC841/ADuC842/ADuC843
In general-purpose I/O port mode, Port 2 pins that have 1s written to them are pulled high by the internal pull-ups (Figure 60) and, in that state, can be used as inputs. As inputs, Port 2 pins being pulled externally low source current because of the internal pull-up resistors. Port 2 pins with 0s written to them drive a logic low output voltage (VOL) and are capable of sinking 1.6 mA. P2.6 and P2.7 can also be used as PWM outputs. When they are selected as the PWM outputs via the CFG841/CFG842 SFR, the PWM outputs overwrite anything written to P2.6 or P2.7.
READ LATCH ADDR CONTROL DVDD DVDD INTERNAL PULL-UP* D CL Q P2.x PIN
03260-0-058
P3.3 and P3.4 can also be used as PWM outputs. When they are selected as the PWM outputs via the CFG841/CFG842 SFR, the PWM outputs overwrite anything written to P3.4 or P3.3.
DVDD READ LATCH ALTERNATE OUTPUT FUNCTION INTERNAL PULL-UP* P3.x PIN
INTERNAL BUS WRITE TO LATCH
D
Q
CL Q LATCH
ALTERNATE INPUT FUNCTION
* SEE PREVIOUS FIGURE FOR DETAILS OF INTERNAL PULL-UP
INTERNAL BUS WRITE TO LATCH READ PIN
Figure 61. Port 3 Bit Latch and I/O Buffer
Q LATCH
* SEE FOLLOWING FIGURE FOR DETAILS OF INTERNAL PULL-UP
Additional Digital I/O
In addition to the port pins, the dedicated SPI/I2C pins (SCLOCK and SDATA/MOSI) also feature both input and output functions. Their equivalent I/O architectures are illustrated in Figure 62 and Figure 64, respectively, for SPI operation and in Figure 63 and Figure 65 for I2C operation. Notice that in I2C mode (SPE = 0), the strong pull-up FET (Q1) is disabled, leaving only a weak pull-up (Q2) present. By contrast, in SPI mode (SPE = 1) the strong pull-up FET (Q1) is controlled directly by SPI hardware, giving the pin push-pull capability. In I2C mode (SPE = 0), two pull-down FETs (Q3 and Q4) operate in parallel to provide an extra 60% or 70% of current sinking capability. In SPI mode (SPE = 1), however, only one of the pull-down FETs (Q3) operates on each pin, resulting in sink capabilities identical to that of Port 0 and Port 2 pins. On the input path of SCLOCK, notice that a Schmitt trigger conditions the signal going to the SPI hardware to prevent false triggers (double triggers) on slow incoming edges. For incoming signals from the SCLOCK and SDATA pins going to I2C hardware, a filter conditions the signals to reject glitches of up to 50 ns in duration. Notice also that direct access to the SCLOCK and SDATA/ MOSI pins is afforded through the SFR interface in I2C master mode. Therefore, if you are not using the SPI or I2C functions, you can use these two pins to give additional high current digital outputs.
SPE = 1 (SPI ENABLE) DVDD Q1 Q2 (OFF) HARDWARE SPI (MASTER/SLAVE) SCHMITT TRIGGER Q3 Q4 (OFF)
03260-0-061
Figure 59. Port 2 Bit Latch and I/O Buffer
DVDD 2 CLK DELAY DVDD DVDD
Q1
Q2
Q3
Figure 60. Internal Pull-Up Configuration
Port 3
Port 3 is a bidirectional port with internal pull-ups directly controlled via the P3 SFR. Port 3 pins that have 1s written to them are pulled high by the internal pull-ups and, in that state, can be used as inputs. As inputs, Port 3 pins being pulled externally low source current because of the internal pull-ups. Port 3 pins with 0s written to them will drive a logic low output voltage (VOL) and are capable of sinking 4 mA. Port 3 pins also have various secondary functions as described in Table 26. The alternate functions of Port 3 pins can be activated only if the corresponding bit latch in the P3 SFR contains a 1. Otherwise, the port pin is stuck at 0.
Table 26. Port 3 Alternate Pin Functions
Pin No. P3.0 P3.1 P3.2 P3.3 P3.4 P3.5 P3.6 P3.7 Alternate Function RxD (UART Input Pin) (or Serial Data I/O in Mode 0) TxD (UART Output Pin) (or Serial Clock Output in Mode 0) INT0 (External Interrupt 0) INT1 (External Interrupt 1)/PWM 1/MISO T0 (Timer/Counter 0 External Input) PWM External Clock/PWM 0 T1 (Timer/Counter 1 External Input) WR (External Data Memory Write Strobe) RD (External Data Memory Read Strobe)
03260-0-059
Q FROM PORT LATCH
Q4
Px.x PIN
SCLOCK PIN
Figure 62. SCLOCK Pin I/O Functional Equivalent in SPI Mode
Rev. 0 | Page 58 of 88
03260-0-060
READ PIN
ADuC841/ADuC842/ADuC843
MOSI is shared with P3.3 and, as such, has the same configuration as the one shown in Figure 61.
SPE = 0 (I2C ENABLE) HARDWARE I2C (SLAVE ONLY) SFR BITS 50ns GLITCH REJECTION FILTER DVDD Q1 (OFF) Q2 SCLOCK PIN MCO I2C M Q3 Q4
03260-0-062
Read-Modify-Write Instructions
Some 8051 instructions that read a port read the latch while others read the pin. The instructions that read the latch rather than the pins are the ones that read a value, possibly change it, and then rewrite it to the latch. These are called read-modifywrite instructions, which are listed below. When the destination operand is a port or a port bit, these instructions read the latch rather than the pin.
Table 27. Read-Write-Modify Instructions
Instruction ANL ORL XRL JBC CPL INC DEC DJNZ MOV PX.Y, C1 CLR PX.Y1 SETB PX.Y1
1
03260-0-097
Figure 63. SCLOCK Pin I/O Functional Equivalent in I2C Mode
SPE = 1 (SPI ENABLE)
DVDD Q1 Q2 (OFF)
HARDWARE SPI (MASTER/SLAVE) Q4 (OFF) Q3
SDATA/ MOSI PIN
Figure 64. SDATA/MOSI Pin I/O Functional Equivalent in SPI Mode
Description Logical AND, e.g., ANL P1, A (Logical OR, e.g., ORL P2, A (Logical EX-OR, e.g., XRL P3, A Jump if Bit = 1 and clear bit, e.g., JBC P1.1, LABEL Complement bit, e.g., CPL P3.0 Increment, e.g., INC P2 Decrement, e.g., DEC P2 Decrement and Jump if Not Zero, e.g., DJNZ P3, LABEL Move Carry to Bit Y of Port X Clear Bit Y of Port X Set Bit Y of Port X
These instructions read the port byte (all 8 bits), modify the addressed bit, and then write the new byte back to the latch.
DVDD SPE = 0 (I2C ENABLE) Q1 (OFF) Q2 50ns GLITCH REJECTION FILTER SDATA/ MOSI PIN Q4
SFR BITS
HARDWARE I2C (SLAVE ONLY)
MCI
MCO Q3
Read-modify-write instructions are directed to the latch rather than to the pin to avoid a possible misinterpretation of the voltage level of a pin. For example, a port pin might be used to drive the base of a transistor. When 1 is written to the bit, the transistor is turned on. If the CPU then reads the same port bit at the pin rather than the latch, it reads the base voltage of the transistor and interprets it as a Logic 0. Reading the latch rather than the pin returns the correct value of 1.
03260-0-063
MDE
I2C M
Figure 65. SDATA/MOSI Pin I/O Functional Equivalent in I2C Mode
Rev. 0 | Page 59 of 88
ADuC841/ADuC842/ADuC843
Timers/Counters
The ADuC841/ADuC842/ADuC843 have three 16-bit timer/ counters: Timer 0, Timer 1, and Timer 2. The timer/counter hardware is included on-chip to relieve the processor core of the overhead inherent in implementing timer/counter functionality in software. Each timer/counter consists of two 8-bit registers: THx and TLx (x = 0, 1, and 2). All three can be configured to operate either as timers or as event counters. In timer function, the TLx register is incremented every machine cycle. Thus, one can think of it as counting machine cycles. Since a machine cycle on a single-cycle core consists of one core clock period, the maximum count rate is the core clock frequency. In counter function, the TLx register is incremented by a 1-to-0 transition at its corresponding external input pin: T0, T1, or T2. When the samples show a high in one cycle and a low in the next cycle, the count is incremented. Since it takes two machine cycles (two core clock periods) to recognize a 1-to-0 transition, the maximum count rate is half the core clock frequency.
Table 28. TMOD SFR Bit Designations
Bit No. 7 Name Gate Description Timer 1 Gating Control. Set by software to enable Timer/Counter 1 only while the INT1 pin is high and the TR1 control bit is set. Cleared by software to enable Timer 1 whenever the TR1 control bit is set. Timer 1 Timer or Counter Select Bit. Set by software to select counter operation (input from T1 pin). Cleared by software to select timer operation (input from internal system clock). Timer 1 Mode Select Bit 1 (Used with M0 Bit). Timer 1 Mode Select Bit 0. M1 M0 0 0 TH1 operates as an 8-bit timer/counter. TL1 serves as 5-bit prescaler. 0 1 16-Bit Timer/Counter. TH1 and TL1 are cascaded; there is no prescaler. 1 0 8-Bit Autoreload Timer/Counter. TH1 holds a value that is to be reloaded into TL1 each time it overflows. 1 1 Timer/Counter 1 Stopped. Timer 0 Gating Control. Set by software to enable Timer/Counter 0 only while the INT0 pin is high and the TR0 control bit is set. Cleared by software to enable Timer 0 whenever the TR0 control bit is set. Timer 0 Timer or Counter Select Bit. Set by software to select counter operation (input from T0 pin). Cleared by software to select timer operation (input from internal system clock). Timer 0 Mode Select Bit 1. Timer 0 Mode Select Bit 0. M1 M0 0 0 TH0 operates as an 8-bit timer/counter. TL0 serves as a 5-bit prescaler. 0 1 16-Bit Timer/Counter. TH0 and TL0 are cascaded; there is no prescaler. 1 0 8-Bit Autoreload Timer/Counter. TH0 holds a value that is to be reloaded into TL0 each time it overflows. 1 1 TL0 is an 8-bit timer/counter controlled by the standard Timer 0 control bits. TH0 is an 8-bit timer only, controlled by Timer 1 control bits.
There are no restrictions on the duty cycle of the external input signal, but to ensure that a given level is sampled at least once before it changes, it must be held for a minimum of one full machine cycle. User configuration and control of all timer operating modes is achieved via three SFRs:
TMOD, TCON T2CON TMOD
Control and configuration for Timers 0 and 1. Control and configuration for Timer 2. Timer/Counter 0 and 1 Mode Register 89H 00H No
SFR Address Power-On Default Bit Addressable
6
C/T
5 4
M1 M0
3
Gate
2
C/T
1 0
M1 M0
Rev. 0 | Page 60 of 88
ADuC841/ADuC842/ADuC843
TCON Timer/Counter 0 and 1 Control Register
SFR Address Power-On Default Bit Addressable
88H 00H Yes
Table 29. TCON SFR Bit Designations
Bit No. 7 Name TF1 Description Timer 1 Overflow Flag. Set by hardware on a Timer/Counter 1 overflow. Cleared by hardware when the program counter (PC) vectors to the interrupt service routine. Timer 1 Run Control Bit. Set by the user to turn on Timer/Counter 1. Cleared by the user to turn off Timer/Counter 1. Timer 0 Overflow Flag. Set by hardware on a Timer/Counter 0 overflow. Cleared by hardware when the PC vectors to the interrupt service routine. Timer 0 Run Control Bit. Set by the user to turn on Timer/Counter 0. Cleared by the user to turn off Timer/Counter 0. External Interrupt 1 (INT1) Flag. Set by hardware by a falling edge or by a zero level being applied to the external interrupt pin, INT1, depending on the state of Bit IT1. Cleared by hardware when the PC vectors to the interrupt service routine only if the interrupt was transitionactivated. If level-activated, the external requesting source controls the request flag, rather than the on-chip hardware. External Interrupt 1 (IE1) Trigger Type. Set by software to specify edge-sensitive detection, i.e., 1-to-0 transition. Cleared by software to specify level-sensitive detection, i.e., zero level. External Interrupt 0 (INT0) Flag. Set by hardware by a falling edge or by a zero level being applied to external interrupt pin INT0, depending on the state of Bit IT0. Cleared by hardware when the PC vectors to the interrupt service routine only if the interrupt was transitionactivated. If level-activated, the external requesting source controls the request flag, rather than the on-chip hardware. External Interrupt 0 (IE0) Trigger Type. Set by software to specify edge-sensitive detection, i.e.,1-to-0 transition. Cleared by software to specify level-sensitive detection, i.e., zero level.
6
TR1
5
TF0
4
TR0
3
IE11
2
IT11
1
IE01
0
IT01
1
These bits are not used in the control of Timer/Counter 0 and 1, but are used instead in the control and monitoring of the external INT0 and INT1 interrupt pins.
Timer/Counter 0 and 1 Data Registers
TH0 and TL0
Each timer consists of two 8-bit registers. These can be used as independent registers or combined into a single 16-bit register depending on the timer mode configuration.
Timer 0 high byte and low byte. SFR Address = 8CH 8AH, respectively.
TH1 and TL1
Timer 1 high byte and low byte. SFR Address = 8DH, 8BH, respectively.
Rev. 0 | Page 61 of 88
ADuC841/ADuC842/ADuC843
TIMER/COUNTER 0 AND 1 OPERATING MODES
The following sections describe the operating modes for Timer/Counters 0 and 1. Unless otherwise noted, assume that these modes of operation are the same for both Timer 0 and Timer 1.
Mode 2 (8-Bit Timer/Counter with Autoreload)
Mode 2 configures the timer register as an 8-bit counter (TL0) with automatic reload, as shown in Figure 68. Overflow from TL0 not only sets TF0, but also reloads TL0 with the contents of TH0, which is preset by software. The reload leaves TH0 unchanged.
CORE CLK C/T = 0 TL0 (8 BITS) TF0 INTERRUPT
Mode 0 (13-Bit Timer/Counter)
Mode 0 configures an 8-bit timer/counter. Figure 66 shows Mode 0 operation. Note that the divide-by-12 prescaler is not present on the single-cycle core.
CORE CLK
C/T = 1 P3.4/T0
C/T = 0 TH0 Tl0 (5 BITS) (8 BITS) C/T = 1 TF0 INTERRUPT
CONTROL
TR0
03260-0-067
P3.4/T0
TR0 CONTROL
GATE P3.2/INT0
RELOAD TH0 (8 BITS)
Figure 68. Timer/Counter 0, Mode 2
GATE P3.2/INT0
03260-0-064
Mode 3 (Two 8-Bit Timer/Counters)
Mode 3 has different effects on Timer 0 and Timer 1. Timer 1 in Mode 3 simply holds its count. The effect is the same as setting TR1 = 0. Timer 0 in Mode 3 establishes TL0 and TH0 as two separate counters. This configuration is shown in Figure 69. TL0 uses the Timer 0 control bits: C/T, Gate, TR0, INT0, and TF0. TH0 is locked into a timer function (counting machine cycles) and takes over the use of TR1 and TF1 from Timer 1. Thus, TH0 now controls the Timer 1 interrupt. Mode 3 is provided for applications requiring an extra 8-bit timer or counter. When Timer 0 is in Mode 3, Timer 1 can be turned on and off by switching it out of and into its own Mode 3, or it can still be used by the serial interface as a baud rate generator. In fact, it can be used in any application not requiring an interrupt from Timer 1 itself.
CORE CLK
Figure 66. Timer/Counter 0, Mode 0
In this mode, the timer register is configured as a 13-bit register. As the count rolls over from all 1s to all 0s, it sets the timer overflow flag, TF0. TF0 can then be used to request an interrupt. The counted input is enabled to the timer when TR0 = 1 and either Gate = 0 or INT0 = 1. Setting Gate = 1 allows the timer to be controlled by external input INT0 to facilitate pulse-width measurements. TR0 is a control bit in the special function register TCON; Gate is in TMOD. The 13-bit register consists of all 8 bits of TH0 and the lower five bits of TL0. The upper 3 bits of TL0 are indeterminate and should be ignored. Setting the run flag (TR0) does not clear the registers.
Mode 1 (16-Bit Timer/Counter)
Mode 1 is the same as Mode 0, except that the Mode 1 timer register is running with all 16 bits. Mode 1 is shown in Figure 67.
CORE CLK
C/T = 0 TL0 TH0 (8 BITS) (8 BITS) C/T = 1 TF0
C/ T = 0
TL0 (8 BITS) TF0
INTERRUPT
C/ T = 1
INTERRUPT
P3.4/T0
CONTROL TR0
P3.4/T0 CONTROL
TR0
03260-0-066
GATE P3.2/INT0
GATE
P3.2/INT0
Figure 67. Timer/Counter 0, Mode 1
CORE CLK/12 TR1
TH0 (8 BITS)
INTERRUPT TF1
Figure 69. Timer/Counter 0, Mode 3
Rev. 0 | Page 62 of 88
03260-0-068
ADuC841/ADuC842/ADuC843
T2CON Timer/Counter 2 Control Register
SFR Address Power-On Default Bit Addressable
C8H 00H Yes
Table 30. T2CON SFR Bit Designations
Bit No. 7 Name TF2 Description Timer 2 Overflow Flag. Set by hardware on a Timer 2 overflow. TF2 cannot be set when either RCLK = 1 or TCLK = 1. Cleared by user software. Timer 2 External Flag. Set by hardware when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1. Cleared by user software. Receive Clock Enable Bit. Set by the user to enable the serial port to use Timer 2 overflow pulses for its receive clock in serial port Modes 1 and 3. Cleared by the user to enable Timer 1 overflow to be used for the receive clock. Transmit Clock Enable Bit. Set by the user to enable the serial port to use Timer 2 overflow pulses for its transmit clock in serial port Modes 1 and 3. Cleared by the user to enable Timer 1 overflow to be used for the transmit clock. Timer 2 External Enable Flag. Set by the user to enable a capture or reload to occur as a result of a negative transition on T2EX if Timer 2 is not being used to clock the serial port. Cleared by the user for Timer 2 to ignore events at T2EX. Timer 2 Start/Stop Control Bit. Set by the user to start Timer 2. Cleared by the user to stop Timer 2. Timer 2 Timer or Counter Function Select Bit. Set by the user to select counter function (input from external T2 pin). Cleared by the user to select timer function (input from on-chip core clock). Timer 2 Capture/Reload Select Bit. Set by the user to enable captures on negative transitions at T2EX if EXEN2 = 1. Cleared by the user to enable autoreloads with Timer 2 overflows or negative transitions at T2EX when EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is forced to autoreload on Timer 2 overflow.
6
EXF2
5
RCLK
4
TCLK
3
EXEN2
2
TR2
1
CNT2
0
CAP2
Timer/Counter 2 Data Registers
Timer/Counter 2 also has two pairs of 8-bit data registers associated with it. These are used as both timer data registers and as timer capture/reload registers.
TH2 and TL2
Timer 2, data high byte and low byte. SFR Address = CDH, CCH, respectively.
RCAP2H and RCAP2L
Timer 2, capture/reload byte and low byte. SFR Address = CBH, CAH, respectively.
Rev. 0 | Page 63 of 88
ADuC841/ADuC842/ADuC843
TIMER/COUNTER OPERATING MODES
The following sections describe the operating modes for Timer/Counter 2. The operating modes are selected by bits in the T2CON SFR, as shown in Table 31.
Table 31. T2CON Operating Modes
RCLK (or) TCLK 0 0 1 X CAP2 0 1 X X TR2 1 1 1 0 Mode 16-Bit Autoreload 16-Bit Capture Baud Rate OFF
16-Bit Capture Mode
Capture mode also has two options that are selected by bit EXEN2 in T2CON. If EXEN2 = 0, then Timer 2 is a 16-bit timer or counter that, upon overflowing, sets Bit TF2, the Timer 2 overflow bit, which can be used to generate an interrupt. If EXEN2 = 1, then Timer 2 still performs the above, but a l-to-0 transition on external input T2EX causes the current value in the Timer 2 registers, TL2 and TH2, to be captured into registers RCAP2L and RCAP2H, respectively. In addition, the transition at T2EX causes Bit EXF2 in T2CON to be set, and EXF2, like TF2, can generate an interrupt. Capture mode is illustrated in Figure 71. The baud rate generator mode is selected by RCLK = 1 and/or TCLK = 1. In either case, if Timer 2 is being used to generate the baud rate, the TF2 interrupt flag will not occur. Therefore, Timer 2 interrupts will not occur, so they do not have to be disabled. In this mode, the EXF2 flag, however, can still cause interrupts, which can be used as a third external interrupt. Baud rate generation is described as part of the UART serial port operation in the following section.
16-Bit Autoreload Mode
Autoreload mode has two options that are selected by Bit EXEN2 in T2CON. If EXEN2 = 0, then when Timer 2 rolls over, it not only sets TF2 but also causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2L and RCAP2H, which are preset by software. If EXEN2 = 1, then Timer 2 still performs the above, but with the added feature that a 1-to-0 transition at external input T2EX will also trigger the 16-bit reload and set EXF2. Autoreload mode is illustrated in Figure 70.
CORE CLK*
C/T2 = 0 TL2 (8 BITS) TH2 (8 BITS)
T2 PIN
C/T2 = 1 CONTROL TR2 RELOAD TRANSITION DETECTOR RCAP2L RCAP2H TF2 TIMER INTERRUPT
T2EX PIN CONTROL EXEN2 * CORE CLK IS DEFINED BY THE CD BITS IN PLLCON
EXF2
Figure 70. Timer/Counter 2, 16-Bit Autoreload Mode
CORE CLK*
C/ T2 = 0 TL2 (8 BITS) TH2 (8 BITS) TF2
T2 PIN
C/ T2 = 1 CONTROL TR2 CAPTURE TRANSITION DETECTOR RCAP2L RCAP2H TIMER INTERRUPT
T2EX PIN CONTROL EXEN2 * CORE CLK IS DEFINED BY THE CD BITS IN PLLCON
EXF2
03260-0-069
Figure 71. Timer/Counter 2, 16-Bit Capture Mode
Rev. 0 | Page 64 of 88
03260-0-070
ADuC841/ADuC842/ADuC843
UART SERIAL INTERFACE
The serial port is full-duplex, meaning it can transmit and receive simultaneously. It is also receive-buffered, meaning it can begin receiving a second byte before a previously received byte has been read from the receive register. However, if the first byte still has not been read by the time reception of the second byte is complete, the first byte is lost. The physical interface to the serial data network is via Pins RxD(P3.0) and TxD(P3.1), while the SFR interface to the UART is comprised of SBUF and SCON, as described below.
Table 32. SCON SFR Bit Designations
Bit No. 7 6 Name SM0 SM1 Description UART Serial Mode Select Bits. These bits select the serial port operating mode as follows: SM0 SM1 Selected Operating Mode. 0 0 Mode 0: Shift Register, fixed baud rate (Core_Clk/2). 0 1 Mode 1: 8-bit UART, variable baud rate. 1 0 Mode 2: 9-bit UART, fixed baud rate (Core_Clk/32) or (Core_Clk/16). 1 1 Mode 3: 9-bit UART, variable baud rate. Multiprocessor Communication Enable Bit. Enables multiprocessor communication in Modes 2 and 3. In Mode 0, SM2 must be cleared. In Mode 1, if SM2 is set, RI is not activated if a valid stop bit was not received. If SM2 is cleared, RI is set as soon as the byte of data has been received. In Modes 2 or 3, if SM2 is set, RI is not activated if the received 9th data bit in RB8 is 0. If SM2 is cleared, RI is set as soon as the byte of data has been received. Serial Port Receive Enable Bit. Set by user software to enable serial port reception. Cleared by user software to disable serial port reception. Serial Port Transmit (Bit 9). The data loaded into TB8 is the 9th data bit transmitted in Modes 2 and 3. Serial Port Receiver Bit 9. The 9th data bit received in Modes 2 and 3 is latched into RB8. For Mode 1, the stop bit is latched into RB8. Serial Port Transmit Interrupt Flag. Set by hardware at the end of the 8th bit in Mode 0, or at the beginning of the stop bit in Modes 1, 2, and 3. TI must be cleared by user software. Serial Port Receive Interrupt Flag. Set by hardware at the end of the 8th bit in Mode 0, or halfway through the stop bit in Modes 1, 2, and 3. RI must be cleared by software.
SBUF
Both the serial port receive and transmit registers are accessed through the SBUF SFR (SFR address = 99H). Writing to SBUF loads the transmit register, and reading SBUF accesses a physically separate receive register.
SCON UART Serial Port Control Register
SFR Address Power-On Default Bit Addressable
98H 00H Yes
5
SM2
4
REN
3 2 1
TB8 RB8 TI
0
RI
Rev. 0 | Page 65 of 88
ADuC841/ADuC842/ADuC843
Mode 0: 8-Bit Shift Register Mode
Mode 0 is selected by clearing both the SM0 and SM1 bits in the SFR SCON. Serial data enters and exits through RxD. TxD outputs the shift clock. Eight data bits are transmitted or received. Transmission is initiated by any instruction that writes to SBUF. The data is shifted out of the RxD line. The 8 bits are transmitted with the least significant bit (LSB) first. Reception is initiated when the receive enable bit (REN) is 1 and the receive interrupt bit (RI) is 0. When RI is cleared, the data is clocked into the RxD line, and the clock pulses are output from the TxD line. This is the case if, and only if, all of the following conditions are met at the time the final shift pulse is generated: * * * RI = 0 Either SM2 = 0 or SM2 = 1 The received stop bit = 1
If any of these conditions is not met, the received frame is irretrievably lost, and RI is not set.
Mode 2: 9-Bit UART with Fixed Baud Rate
Mode 2 is selected by setting SM0 and clearing SM1. In this mode, the UART operates in 9-bit mode with a fixed baud rate. The baud rate is fixed at Core_Clk/32 by default, although by setting the SMOD bit in PCON, the frequency can be doubled to Core_Clk/16. Eleven bits are transmitted or received: a start bit (0), 8 data bits, a programmable 9th bit, and a stop bit (1). The 9th bit is most often used as a parity bit, although it can be used for anything, including a 9th data bit if required. To transmit, the 8 data bits must be written into SBUF. The 9th bit must be written to TB8 in SCON. When transmission is initiated, the 8 data bits (from SBUF) are loaded onto the transmit shift register (LSB first). The contents of TB8 are loaded into the 9th bit position of the transmit shift register. The transmission starts at the next valid baud rate clock. The TI flag is set as soon as the stop bit appears on TxD. Reception for Mode 2 is similar to that of Mode 1. The 8 data bytes are input at RxD (LSB first) and loaded onto the receive shift register. When all 8 bits have been clocked in, the following events occur: * * * The 8 bits in the receive shift register are latched into SBUF. The 9th data bit is latched into RB8 in SCON. The receiver interrupt flag (RI) is set.
Mode 1: 8-Bit UART, Variable Baud Rate
Mode 1 is selected by clearing SM0 and setting SM1. Each data byte (LSB first) is preceded by a start bit (0) and followed by a stop bit (1). Therefore, 10 bits are transmitted on TxD or are received on RxD. The baud rate is set by the Timer 1 or Timer 2 overflow rate, or a combination of the two (one for transmission and the other for reception). Transmission is initiated by writing to SBUF. The write to SBUF signal also loads a 1 (stop bit) into the 9th bit position of the transmit shift register. The data is output bit by bit until the stop bit appears on TxD and the transmit interrupt flag (TI) is automatically set, as shown in Figure 72.
START BIT
TxD
STOP BIT D0 D1 D2 D3 D4 D5 D6 D7
SET INTERRUPT I.E., READY FOR MORE DATA
Figure 72. UART Serial Port Transmission, Mode 1
Reception is initiated when a 1-to-0 transition is detected on RxD. Assuming a valid start bit is detected, character reception continues. The start bit is skipped and the 8 data bits are clocked into the serial port shift register. When all 8 bits have been clocked in, the following events occur: * * * The 8 bits in the receive shift register are latched into SBUF. The 9th bit (stop bit) is clocked into RB8 in SCON. The receiver interrupt flag (RI) is set.
03260-0-072
TI (SCON.1)
This is the case if, and only if, all of the following conditions are met at the time the final shift pulse is generated: * * * RI = 0 Either SM2 = 0 or SM2 = 1 The received stop bit = 1
If any of these conditions is not met, the received frame is irretrievably lost, and RI is not set.
Rev. 0 | Page 66 of 88
ADuC841/ADuC842/ADuC843
Mode 3: 9-Bit UART with Variable Baud Rate
Mode 3 is selected by setting both SM0 and SM1. In this mode, the 8051 UART serial port operates in 9-bit mode with a variable baud rate determined by either Timer 1 or Timer 2. The operation of the 9-bit UART is the same as for Mode 2, but the baud rate can be varied as for Mode 1. In all four modes, transmission is initiated by any instruction that uses SBUF as a destination register. Reception is initiated in Mode 0 by the condition RI = 0 and REN = 1. Reception is initiated in the other modes by the incoming start bit if REN = 1. The Timer 1 interrupt should be disabled in this application. The timer itself can be configured for either timer or counter operation, and in any of its three running modes. In the most typical application, it is configured for timer operation in the autoreload mode (high nibble of TMOD = 0010 binary). In that case, the baud rate is given by the formula Modes 1 and 3 Baud Rate = (2SMOD/32) x (Core Clock/ [256 - TH1])
Timer 2 Generated Baud Rates
Baud rates can also be generated using Timer 2. Using Timer 2 is similar to using Timer 1 in that the timer must overflow 16 times before a bit is transmitted/received. Because Timer 2 has a 16-bit autoreload mode, a wider range of baud rates is possible using Timer 2. Modes 1 and 2 Baud Rate = (1/16) x (Timer 2 Overflow Rate) Therefore, when Timer 2 is used to generate baud rates, the timer increments every two clock cycles rather than every core machine cycle as before. Thus, it increments six times faster than Timer 1, and therefore baud rates six times faster are possible. Because Timer 2 has 16-bit autoreload capability, very low baud rates are still possible. Timer 2 is selected as the baud rate generator by setting the TCLK and/or RCLK in T2CON. The baud rates for transmit and receive can be simultaneously different. Setting RCLK and/ or TCLK puts Timer 2 into its baud rate generator mode as shown in Figure 73. In this case, the baud rate is given by the formula Modes 1 and 3 Baud Rate = (Core Clock)/(16 x [65536 - (RCAP 2H, RCAP 2L)])
TIMER 1 OVERFLOW
UART Serial Port Baud Rate Generation
Mode 0 Baud Rate Generation
The baud rate in Mode 0 is fixed. Mode 0 Baud Rate = (Core Clock Frequency/12)
Mode 2 Baud Rate Generation
The baud rate in Mode 2 depends on the value of the SMOD bit in the PCON SFR. If SMOD = 0, the baud rate is 1/32 of the core clock. If SMOD = 1, the baud rate is 1/16 of the core clock: Mode 2 Baud Rate = (2SMOD/32 x [Core Clock Frequency])
Modes 1 and 3 Baud Rate Generation
The baud rates in Modes 1 and 3 are determined by the overflow rate in Timer 1 or Timer 2, or in both (one for transmit and the other for receive).
Timer 1 Generated Baud Rates
When Timer 1 is used as the baud rate generator, the baud rates in Modes 1 and 3 are determined by the Timer 1 overflow rate and the value of SMOD as follows: Modes 1 and 3 Baud Rate = (2SMOD/32 x (Timer 1 Overflow Rate)
2 0 CORE CLK* CONTROL C/ T2 = 0 TL2 (8 BITS) T2 PIN C/ T2 = 1 1 TR2 NOTE: AVAILABILITY OF ADDITIONAL EXTERNAL INTERRUPT RCAP2L RCAP2H RELOAD 16 0 TCLK TX CLOCK TH2 (8 BITS) TIMER 2 OVERFLOW 1 0 RCLK 16 RX CLOCK 1 SMOD
T2EX PIN CONTROL EXEN2
EXF 2
TIMER 2 INTERRUPT
*CORE CLK IS DEFINED BY THE CD BITS IN PLLCON
Figure 73. Timer 2, UART Baud Rates
Rev. 0 | Page 67 of 88
03260-0-073
TRANSITION DETECTOR
ADuC841/ADuC842/ADuC843
Timer 3 Generated Baud Rates
The high integer dividers in a UART block mean that high speed baud rates are not always possible using some particular crystals. For example, using a 12 MHz crystal, a baud rate of 115200 is not possible. To address this problem, the part has added a dedicated baud rate timer (Timer 3) specifically for generating highly accurate baud rates. Timer 3 can be used instead of Timer 1 or Timer 2 for generating very accurate high speed UART baud rates including 115200 and 230400. Timer 3 also allows a much wider range of baud rates to be obtained. In fact, every desired bit rate from 12 bit/s to 393216 bit/s can be generated to within an error of 0.8%. Timer 3 also frees up the other three timers, allowing them to be used for different applications. A block diagram of Timer 3 is shown in Figure 74.
CORE CLK 2 TIMER 1/TIMER 2 TX CLOCK FRACTIONAL DIVIDER
(1 + T3FD/64)
The appropriate value to write to the DIV2-1-0 bits can be calculated using the following formula where fCORE is defined in PLLCON SFR. Note that the DIV value must be rounded down.
f CORE log 16 x Baud Rate DIV = log (2)
T3FD is the fractional divider ratio required to achieve the required baud rate. The appropriate value for T3FD can be calculated with the following formula:
T 3FD =
2
DIV -1
2 x f CORE - 64 x Baud Rate
TIMER 1/TIMER 2 RX CLOCK 1 0
Note that T3FD should be rounded to the nearest integer. Once the values for DIV and T3FD are calculated, the actual baud rate can be calculated with the following formula:
2DIV RX CLOCK 16 T3 RX/TX CLOCK T3EN TX CLOCK
03260-0-074
Actual Baud Rate =
2
DIV -1
2 x f CORE x (T 3FD + 64 )
1
0
For example, to get a baud rate of 115200 while operating at 16.7 MHz, i.e., CD = 0
Figure 74. Timer 3, UART Baud Rates
DIV = log(16777216 / (16 x 115200)) / log 2 = 3.18 = 3 T 3FD = (2 x 16777216) / 2 2 x 115200 - 64 = 9 = 09 H Therefore, the actual baud rate is 114912 bit/s.
Two SFRs (T3CON and T3FD) are used to control Timer 3. T3CON is the baud rate control SFR, allowing Timer 3 to be used to set up the UART baud rate, and setting up the binary divider (DIV).
Table 33. T3CON SFR Bit Designations
Bit No. 7 Name T3BAUDEN
(
)
6 5 4 3 2 1 0
DIV2 DIV1 DIV0
Description T3UARTBAUD Enable. Set to enable Timer 3 to generate the baud rate. When set, PCON.7, T2CON.4, and T2CON.5 are ignored. Cleared to let the baud rate be generated as per a standard 8052. Reserved. Reserved. Reserved. Reserved. Binary Divider Factor. DIV2 DIV1 DIV0 Bin Divider 0 0 0 1 0 0 1 1 0 1 0 1 0 1 1 1 1 0 0 1 1 0 1 1 1 1 0 1 1 1 1 1
Rev. 0 | Page 68 of 88
ADuC841/ADuC842/ADuC843
Table 34. Commonly Used Baud Rates Using Timer 3 with the 16.777216 MHz PLL Clock
Ideal Baud 230400 115200 115200 115200 57600 57600 57600 57600 38400 38400 38400 38400 19200 19200 19200 19200 19200 9600 9600 9600 9600 9600 9600 CD 0 0 1 2 0 1 2 3 0 1 2 3 0 1 2 3 4 0 1 2 3 4 5 DIV 2 3 2 1 4 3 2 1 4 3 2 1 5 4 3 2 1 6 5 4 3 2 1 T3CON 82H 83H 82H 81H 84H 83H 82H 81H 84H 83H 82H 81H 85H 84H 83H 82H 81H 86H 85H 84H 83H 82H 81H T3FD 09H 09H 09H 09H 09H 09H 09H 09H 2DH 2DH 2DH 2DH 2DH 2DH 2DH 2DH 2DH 2DH 2DH 2DH 2DH 2DH 2DH % Error 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2
Rev. 0 | Page 69 of 88
ADuC841/ADuC842/ADuC843
INTERRUPT SYSTEM
The ADuC841/ADuC842/ADuC843 provide a total of nine interrupt sources with two priority levels. The control and configuration of the interrupt system is carried out through three interrupt-related SFRs:
IE IP IEIP2
Interrupt Enable Register Interrupt Priority Register Secondary Interrupt Enable Register
IE
Interrupt Enable Register
SFR Address Power-On Default Bit Addressable
A8H 00H Yes
Table 35. IE SFR Bit Designations
Bit No. 7 6 5 4 3 2 1 0 Name EA EADC ET2 ES ET1 EX1 ET0 EX0 Description Set by the user to enable, or cleared to disable all interrupt sources. Set by the user to enable, or cleared to disable ADC interrupts. Set by the user to enable, or cleared to disable Timer 2 interrupts. Set by the user to enable, or cleared to disable UART serial port interrupts. Set by the user to enable, or cleared to disable 0 Timer 1 interrupts. Set by the user to enable, or cleared to disable External Interrupt 1. Set by the user to enable, or cleared to disable Timer 0 interrupts. Set by the user to enable, or cleared to disable External Interrupt 0 .
IP SFR Address Power-On Default Bit Addressable
Interrupt Priority Register B8H 00H Yes
Table 36. IP SFR Bit Designations
Bit No. 7 6 5 4 3 2 1 0 Name ---PADC PT2 PS PT1 PX1 PT0 PX0 Description Reserved. Written by the user to select the ADC interrupt priority (1 = High; 0 = Low). Written by the user to select the Timer 2 interrupt priority (1 = High; 0 = Low). Written by the user to select the UART serial port interrupt priority (1 = High; 0 = Low). Written by the user to select the Timer 1 interrupt priority (1 = High; 0 = Low). Written by the user to select External Interrupt 1 priority (1 = High; 0 = Low). Written by the user to select the Timer 0 interrupt priority (1 = High; 0 = Low). Written by the user to select External Interrupt 0 priority (1 = High; 0 = Low).
Rev. 0 | Page 70 of 88
ADuC841/ADuC842/ADuC843
IEIP2 SFR Address Power-On Default Bit Addressable Secondary Interrupt Enable Register A9H A0H No
Table 37. IEIP2 SFR Bit Designations
Bit No. 7 6 5 4 3 2 1 0 Name ---PTI PPSM PSI ---ETI EPSMI ESI Description Reserved. Priority for time interval interrupt. Priority for power supply monitor interrupt. Priority for SPI/I2C interrupt. This bit must contain zero. Set by the user to enable, or cleared to disable time interval counter interrupts. Set by the user to enable, or cleared to disable power supply monitor interrupts. Set by the user to enable, or cleared to disable SPI or I2C serial port interrupts.
Interrupt Priority
The interrupt enable registers are written by the user to enable individual interrupt sources, while the interrupt priority registers allow the user to select one of two priority levels for each interrupt. An interrupt of a high priority may interrupt the service routine of a low priority interrupt, and if two interrupts of different priority occur at the same time, the higher level interrupt is serviced first. An interrupt cannot be interrupted by another interrupt of the same priority level. If two interrupts of the same priority level occur simultaneously, a polling sequence is observed as shown in Table 38.
Table 38. Priority within an Interrupt Level
Source PSMI WDS IE0 ADCI TF0 IE1 TF1 ISPI/I2CI RI + TI TF2 + EXF2 TII Priority 1 (Highest) 2 2 3 4 5 6 7 8 9 11(Lowest) Description Power Supply Monitor Interrupt. Watchdog Timer Interrupt. External Interrupt 0. ADC Interrupt. Timer/Counter 0 Interrupt. External Interrupt 1. Timer/Counter 1 Interrupt. SPI Interrupt/I2C Interrupt. Serial Interrupt. Timer/Counter 2 Interrupt. Time Interval Counter Interrupt.
Interrupt Vectors
When an interrupt occurs, the program counter is pushed onto the stack, and the corresponding interrupt vector address is loaded into the program counter. The interrupt vector addresses are shown in Table 39.
Table 39. Interrupt Vector Addresses
Source IE0 TF0 IE1 TF1 RI + TI TF2 + EXF2 ADCI ISPI/I2CI PSMI TII WDS Vector Address 0003H 000BH 0013H 001BH 0023H 002BH 0033H 003BH 0043H 0053H 005BH
Rev. 0 | Page 71 of 88
ADuC841/ADuC842/ADuC843
HARDWARE DESIGN CONSIDERATIONS
This section outlines some of the key hardware design considerations that must be addressed when integrating the ADuC841/ADuC842/ADuC843 into any hardware system.
ADuC842/ADuC843
EXTERNAL CLOCK SOURCE P3.4 TO INTERNAL TIMING CIRCUITS
Clock Oscillator
The clock source for the parts can be generated by the internal PLL or by an external clock input. To use the internal PLL, connect a 32.768 kHz parallel resonant crystal between XTAL1 and XTAL2, and connect a capacitor from each pin to ground as shown in Figure 75. The parts contain an internal capacitance of 18 pF on the XTAL1 and XTAL2 pins, which is sufficient for most watch crystals. This crystal allows the PLL to lock correctly to give an fVCO of 16.777216 MHz. If no crystal is present, the PLL will free run, giving an fVCO of 16.7 MHz 20%. In this mode, the CD bits are limited to CD = 1, giving a max core clock of 8.38 MHz. This is useful if an external clock input is required. The part powers up and the PLL will free run; the user then writes to the CFG842 SFR in software to enable the external clock input on P3.4. Note that double the required clock must be provided externally since the part runs at CD = 1. A better solution is to use the ADuC841 with the external clock. For the ADuC841, connect the crystal in the same manner; external capacitors should be connected as per the crystal manufacturer's recommendations. A minimum capacitance of 20 pF is recommended on XTAL1 and XTAL2. The ADuC841 will not operate if no crystal is present. An external clock may be connected as shown in Figure 76 and Figure 77.
ADuC841/ADuC842/ADuC843
XTAL1
Figure 77. Connecting an External Clock Source (ADuC842/ADuC843)
Whether using the internal PLL or an external clock source, the parts' specified operational clock speed range is 400 kHz to 16.777216 MHz, (20 MHz, ADuC841). The core itself is static, and functions all the way down to dc. But at clock speeds slower that 400 kHz, the ADC can no longer function correctly. Therefore, to ensure specified operation, use a clock frequency of at least 400 kHz and no more than 20 MHz.
External Memory Interface
In addition to its internal program and data memories, the parts can access up to 16 MBytes of external data memory (SRAM). Note that the parts cannot access external program memory. Figure 78 shows a hardware configuration for accessing up to 64 kBytes of external RAM. This interface is standard to any 8051 compatible MCU.
ADuC841/ ADuC842/ ADuC843
SRAM P0 LATCH ALE A8-A15 OE WE
03260-0-078
D0-D7 (DATA) A0-A7
XTAL2
03260-0-076
TO INTERNAL TIMING CIRCUITS
P2 RD WR
Figure 75. External Parallel Resonant Crystal Connections
Figure 78. External Data Memory Interface (64 kBytes Address Space)
ADuC841
EXTERNAL XTAL1 CLOCK SOURCE
XTAL2
Figure 76. Connecting an External Clock Source (ADuC841)
03260-0-075
TO INTERNAL TIMING CIRCUITS
Rev. 0 | Page 72 of 88
03260-0-077
ADuC841/ADuC842/ADuC843
If access to more than 64 kBytes of RAM is desired, a feature unique to the ADuC841/ADuC842/ADuC843 allows addressing up to 16 MBytes of external RAM simply by adding an additional latch as illustrated in Figure 79.
ADuC841/ ADuC842/ ADuC843
SRAM
0.1F DIGITAL SUPPLY + - 10F ANALOG SUPPLY 10F + -
DVDD
AVDD
0.1F
P0 LATCH ALE
D0-D7 (DATA) A0-A7
ADuC841/ ADuC842/ ADuC843
DGND AGND
03260-0-080
P2 LATCH
A8-A15
Figure 80. External Dual-Supply Connections
A16-A23
WR
WE
Figure 79. External Data Memory Interface (16 MBytes Address Space)
In either implementation, Port 0 (P0) serves as a multiplexed address/data bus. It emits the low byte of the data pointer (DPL) as an address, which is latched by a pulse of ALE prior to data being placed on the bus by the ADuC841/ADuC842/ADuC843 (write operation) or by the SRAM (read operation). Port 2 (P2) provides the data pointer page byte (DPP) to be latched by ALE, followed by the data pointer high byte (DPH). If no latch is connected to P2, DPP is ignored by the SRAM, and the 8051 standard of 64 kBytes external data memory access is maintained.
03260-0-079
RD
OE
As an alternative to providing two separate power supplies, the user can help keep AVDD quiet by placing a small series resistor and/or ferrite bead between it and DVDD, and then decoupling AVDD separately to ground. An example of this configuration is shown in Figure 81. With this configuration, other analog circuitry (such as op amps and voltage reference) can be powered from the AVDD supply line as well. The user will still want to include back-to-back Schottky diodes between AVDD and DVDD to protect them from power-up and power-down transient conditions that could momentarily separate the two supply voltages.
DIGITAL SUPPLY 10F + - DVDD 0.1F AVDD 0.1F BEAD 1.6 10F
Power Supplies
The operational power supply voltage of the parts depends on whether the part is the 3 V version or the 5 V version. The specifications are given for power supplies within 2.7 V to 3.6 V or 5% of the nominal 5 V level. Note that Figure 80 and Figure 81 refer to the PQFP package. For the CSP package, connect the extra DVDD, DGND, AVDD, and AGND in the same manner. Also, the paddle on the bottom of the package should be soldered to a metal plate to provide mechanical stability. This metal plate should not be connected to ground. Separate analog and digital power supply pins (AVDD and DVDD, respectively) allow AVDD to be kept relatively free of the noisy digital signals that are often present on the system DVDD line. However, though you can power AVDD and DVDD from two separate supplies if desired, you must ensure that they remain within 0.3 V of one another at all times to avoid damaging the chip (as per the Absolute Maximum Ratings section). Therefore, it is recommended that unless AVDD and DVDD are connected directly together, back-to-back Schottky diodes should be connected between them, as shown in Figure 80.
ADuC841/ ADuC842/ ADuC843
DGND AGND
Figure 81. External Single-Supply Connections
Notice that in both Figure 80 and Figure 81, a large value (10 F) reservoir capacitor sits on DVDD and a separate 10 F capacitor sits on AVDD. Also, local small-value (0.1 F) capacitors are located at each VDD pin of the chip. As per standard design practice, be sure to include all of these capacitors, and ensure the smaller capacitors are close to each AVDD pin with trace lengths as short as possible. Connect the ground terminal of each of these capacitors directly to the underlying ground plane. Finally, note that at all times, the analog and digital ground pins on the part must be referenced to the same system ground reference point.
Rev. 0 | Page 73 of 88
03260-0-081
ADuC841/ADuC842/ADuC843
Power Consumption
The currents consumed by the various sections of the part are shown in Table 40. The core values given represent the current drawn by DVDD, while the rest (ADC, DAC, voltage ref) are pulled by the AVDD pin and can be disabled in software when not in use. The other on-chip peripherals (such as the watchdog timer and the power supply monitor) consume negligible current, and are therefore lumped in with the core operating current here. Of course, the user must add any currents sourced by the parallel and serial I/O pins, and sourced by the DAC, in order to determine the total current needed at the supply pins. Also, current drawn from the DVDD supply increases by approximately 10 mA during Flash/EE erase and program cycles.
Table 40. Typical IDD of Core and Peripherals
VDD = 5 V
Core (Normal Mode) ADC DAC (Each) Voltage Ref (2.2 nA x MCLK) 1.7 mA 250 A 200 A
power-down mode, the part consumes a total of approximately 20 A. There are five ways of terminating power-down mode:
Asserting the RESET Pin (Pin 15)
Returns to normal mode. All registers are set to their default state and program execution starts at the reset vector once the RESET pin is de-asserted.
Cycling Power
All registers are set to their default state and program execution starts at the reset vector approximately 128 ms later.
Time Interval Counter (TIC) Interrupt
VDD = 3 V
(1.4 nA x MCLK) 1.7 mA 200 A 150 A
Power-down mode is terminated, and the CPU services the TIC interrupt. The RETI at the end of the TIC ISR returns the core to the instruction after the one that enabled power-down.
I2C or SPI Interrupt
Since operating DVDD current is primarily a function of clock speed, the expressions for core supply current in Table 40 are given as functions of MCLK, the core clock frequency. Plug in a value for MCLK in hertz to determine the current consumed by the core at that oscillator frequency. Since the ADC and DACs can be enabled or disabled in software, add only the currents from the peripherals you expect to use. And again, do not forget to include current sourced by I/O pins, serial port pins, DAC outputs, and so forth, plus the additional current drawn during Flash/EE erase and program cycles. A software switch allows the chip to be switched from normal mode into idle mode, and also into full power-down mode. Brief descriptions of idle and power-down modes follow.
Power-down mode is terminated, and the CPU services the I2C/SPI interrupt. The RETI at the end of the ISR returns the core to the instruction after the one that enabled power-down. Note that the I2C/SPI power-down interrupt enable bit (SERIPD) in the PCON SFR must be set to allow this mode of operation.
INT0 Interrupt
Power-down mode is terminated, and the CPU services the INT0 interrupt. The RETI at the end of the ISR returns the core to the instruction after the one that enabled power-down. The INT0 pin must not be driven low during or within two machine cycles of the instruction that initiates power-down mode. Note that the INT0 power-down interrupt enable bit (INT0PD) in the PCON SFR must be set to allow this mode of operation.
Power-On Reset (POR)
An internal POR is implemented on the ADuC841/ADuC842/ ADuC843.
3 V Part
Power Saving Modes
In idle mode, the oscillator continues to run, but the core clock generated from the PLL is halted. The on-chip peripherals continue to receive the clock, and remain functional. The CPU status is preserved with the stack pointer and program counter, and all other internal registers maintain their data during idle mode. Port pins and DAC output pins retain their states in this mode. The chip recovers from idle mode upon receiving any enabled interrupt, or upon receiving a hardware reset. In full power-down mode, both the PLL and the clock to the core are stopped. The on-chip oscillator can be halted or can continue to oscillate, depending on the state of the oscillator power-down bit in the PLLCON SFR. The TIC, being driven directly from the oscillator, can also be enabled during powerdown. All other on-chip peripherals are, however, shut down. Port pins retain their logic levels in this mode, but the DAC output goes to a high impedance state (three-state). During full
For DVDD below 2.45 V, the internal POR holds the part in reset. As DVDD rises above 2.45 V, an internal timer times out for approximately 128 ms before the part is released from reset. The user must ensure that the power supply has reached a stable 2.7 V minimum level by this time. Likewise on power-down, the internal POR holds the part in reset until the power supply has dropped below 1 V. Figure 82 illustrates the operation of the internal POR in detail.
2.45V TYP DVDD 1.0V TYP 128ms TYP 128ms TYP 1.0V TYP
INTERNAL CORE RESET
Figure 82. Internal POR Operation
Rev. 0 | Page 74 of 88
03260-0-082
ADuC841/ADuC842/ADuC843
5 V Part
For DVDD below 4.5 V, the internal POR holds the part in reset. As DVDD rises above 4.5 V, an internal timer times out for approximately 128 ms before the part is released from reset. The user must ensure that the power supply has reached a stable 4.75 V minimum level by this time. Likewise on power-down, the internal POR holds the part in reset until the power supply has dropped below 1 V. Figure 83 illustrates the operation of the internal POR in detail.
4.75V DVDD 1.0V TYP 128ms 128ms 1.0V
reach their destinations. For example, do not power components on the analog side of Figure 84b with DVDD since that would force return currents from DVDD to flow through AGND. Also, try to avoid digital currents flowing under analog circuitry, which could happen if the user places a noisy digital chip on the left half of the board in Figure 84c. Whenever possible, avoid large discontinuities in the ground plane(s) (like those formed by a long trace on the same layer), since they force return signals to travel a longer path. And of course, make all connections to the ground plane directly, with little or no trace separating the pin from its via to ground. If the user plans to connect fast logic signals (rise/fall time < 5 ns) to any of the part's digital inputs, a series resistor should be added to each relevant line to keep rise and fall times longer than 5 ns at the part's input pins. A value of 100 or 200 is usually sufficient to prevent high speed signals from coupling capacitively into the part and from affecting the accuracy of ADC conversions.
INTERNAL CORE RESET
Figure 83. Internal POR Operation
Grounding and Board Layout Recommendations
As with all high resolution data converters, special attention must be paid to grounding and PC board layout of ADuC841/ ADuC842/ADuC843 based designs to achieve optimum performance from the ADC and the DACs. Although the parts have separate pins for analog and digital ground (AGND and DGND), the user must not tie these to two separate ground planes unless the two ground planes are connected together very close to the part, as illustrated in the simplified example of Figure 84a. In systems where digital and analog ground planes are connected together somewhere else (for example, at the system's power supply), they cannot be connected again near the part since a ground loop would result. In these cases, tie all the part's AGND and DGND pins to the analog ground plane, as illustrated in Figure 84b. In systems with only one ground plane, ensure that the digital and analog components are physically separated onto separate halves of the board such that digital return currents do not flow near analog circuitry and vice versa. The part can then be placed between the digital and analog sections, as illustrated in Figure 84c. In all of these scenarios, and in more complicated real-life applications, keep in mind the flow of current from the supplies and back to ground. Make sure the return paths for all currents are as close as possible to the paths that the currents took to
a.
PLACE ANALOG COMPONENTS HERE AGND PLACE DIGITAL COMPONENTS HERE DGND
03260-0-096
b.
PLACE ANALOG COMPONENTS HERE AGND
PLACE DIGITAL COMPONENTS HERE DGND
c.
PLACE ANALOG COMPONENTS HERE GND
PLACE DIGITAL COMPONENTS HERE
03260-0-083
Figure 84. System Grounding Schemes
Rev. 0 | Page 75 of 88
ADuC841/ADuC842/ADuC843
DOWNLOAD/DEBUG ENABLE JUMPER (NORMALLY OPEN) DVDD 1k DVDD 1k 2-PIN HEADER FOR EMULATION ACCESS (NORMALLY OPEN)
39 38 37 36
52
51
50
49
48
47
46
45
44
43
42
41
40
PSEN
DVDD
ANALOG INPUT
ADC0
AVDD AVDD AGND VREF OUTPUT CREF VREF DAC0 DAC1 DAC OUTPUT
ADuC841/ADuC842/ADuC843
DGND
EA
DVDD
DGND 35 DVDD 34 XTAL2 33 XTAL1 32
31 30 29
11.0592MHz (ADuC841) 32.768kHz (ADuC842/ADuC843)
RESET
DGND
ADC7
DVDD
28 27
RXD
TXD
NOT CONNECTED IN THIS EXAMPLE DVDD
ADM202 C1+ V+ C1- C2+ C2- V- T2OUT R2IN VCC GND T1OUT R1IN R1OUT T1IN T2IN R2OUT
DVDD
9-PIN D-SUB FEMALE 1 2 3 4 5 6
03260-0-084
7 8 9
Figure 85. Example System (PQFP Package), DACs Not Present on ADuC843
OTHER HARDWARE CONSIDERATIONS
To facilitate in-circuit programming, plus in-circuit debug and emulation options, users will want to implement some simple connection points in their hardware to allow easy access to download, debug, and emulation modes. for a simple (and zero-cost-per-board) method of gaining incircuit serial download access to the part. In addition to the basic UART connections, users also need a way to trigger the chip into download mode. This is accomplished via a 1 k pull-down resistor that can be jumpered onto the PSEN pin, as shown in Figure 85. To get the part into download mode, simply connect this jumper and power-cycle the device (or manually reset the device, if a manual reset button is available), and it will be ready to serially receive a new program. With the jumper removed, the device comes up in normal mode (and runs the program) whenever power is cycled or RESET is toggled.
In-Circuit Serial Download Access
Nearly all ADuC841/ADuC842/ADuC843 designs want to take advantage of the in-circuit reprogrammability of the chip. This is accomplished by a connection to the ADuC841/ADuC842/ ADuC843's UART, which requires an external RS-232 chip for level translation if downloading code from a PC. Basic configuration of an RS-232 connection is illustrated in Figure 85 with a simple ADM202 based circuit. If users would rather not design an RS-232 chip onto a board, refer to Application Note uC006, A 4-Wire UART-to-PC Interface, (at www.analog.com/microconverter)
Rev. 0 | Page 76 of 88
ADuC841/ADuC842/ADuC843
Note that PSEN is normally an output (as described in the External Memory Interface section) and is sampled as an input only on the falling edge of RESET, i.e., at power-up or upon an external manual reset. Note also that if any external circuitry unintentionally pulls PSEN low during power-up or reset events, it could cause the chip to enter download mode and therefore fail to begin user code execution as it should. To prevent this, ensure that no external signals are capable of pulling the PSEN pin low, except for the external PSEN jumper itself.
QUICKSTART DEVELOPMENT SYSTEM
The QuickStart Development System is an entry-level, low cost development tool suite supporting the parts. The system consists of the following PC based (Windows(R) compatible) hardware and software development tools. Hardware Software Miscellaneous Evaluation board and serial port programming cable. Serial download software. CD-ROM documentation and prototype device.
Embedded Serial Port Debugger
From a hardware perspective, entry into serial port debug mode is identical to the serial download entry sequence described in the preceding section. In fact, both serial download and serial port debug modes can be thought of as essentially one mode of operation used in two different ways. Note that the serial port debugger is fully contained on the part (unlike ROM monitor type debuggers), and therefore no external memory is needed to enable in-system debug sessions.
A brief description of some of the software tools and components in the QuickStart Development System follows.
Download--In-Circuit Serial Downloader
The serial downloader is a Windows application that allows the user to serially download an assembled program (Intel(R) hexadecimal format file) to the on-chip program flash memory via the serial COM1 port on a standard PC. Application Note uC004 details this serial download protocol and is available from www.analog.com/microconverter.
Single-Pin Emulation Mode
Also built into the part is a dedicated controller for single-pin in-circuit emulation (ICE) using standard production ADuC841/ ADuC842/ADuC843 devices. In this mode, emulation access is gained by connection to a single pin, the EA pin. Normally, this pin is hardwired either high or low to select execution from internal or external program memory space, as described earlier. To enable single-pin emulation mode, however, users need to pull the EA pin high through a 1 k resistor, as shown in Figure 85. The emulator then connects to the 2-pin header also shown in Figure 85. To be compatible with the standard connector that comes with the single-pin emulator available from Accutron Limited (www.accutron.com), use a 2-pin 0.1 inch pitch friction lock header from Molex (www.molex.com) such as their part number 22-27-2021. Be sure to observe the polarity of this header. As represented in Figure 85, when the friction lock tab is at the right, the ground pin should be the lower of the two pins (when viewed from the top).
ASPIRE--IDE
The ASPIRE integrated development environment is a Windows application that allows the user to compile, edit, and debug code in the same environment. The ASPIRE software allows users to debug code execution on silicon using the MicroConverter UART serial port. The debugger provides access to all on-chip peripherals during a typical debug session as well as single step, animate, and break-point code execution control. Note that the ASPIRE IDE is also included as part of the QuickStart Plus System. As part of the QuickStart Plus System, the ASPIRE IDE also supports mixed level and C source debug. This is not available in the QuickStart System, but there is an example project that demonstrates this capability.
QuickStart Plus Development System
The QuickStart Plus Development System offers users enhanced nonintrusive debug and emulation tools. The system consists of the following PC based (Windows compatible) hardware and software development tools. Hardware Software Prototype Board. Accutron Nonintrusive Single-Pin Emulator. ASPIRE Integrated Development Environment. Features full C and assembly emulation using the Accutron single pin emulator. CD-ROM documentation.
Typical System Configuration
The typical configuration shown in Figure 85 summarizes some of the hardware considerations that were discussed in previous sections.
DEVELOPMENT TOOLS
There are two models of development tools available for the ADuC841/ADuC842/ADuC843: * * QuickStartTM--Entry-level development system QuickStart Plus--Comprehensive development system Miscellaneous
These systems are described briefly in the following sections.
Rev. 0 | Page 77 of 88
ADuC841/ADuC842/ADuC843 TIMING SPECIFICATIONS1, 2, 3
Table 41. AVDD =2.7 V to 3.6 V or 4.75 V to 5.25 V, DVDD = 2.7 V to 3.6 V or 4.75 V to 5.25 V; all specifications TMIN to TMAX, unless otherwise noted
Parameter ADuC842/ADuC843 CLOCK INPUT (External Clock Driven XTAL1) tCK XTAL1 Period tCKL XTAL1 Width Low tCKH XTAL1 Width High tCKR XTAL1 Rise Time tCKF XTAL1 Fall Time 1/tCORE ADuC842/ADuC843 Core Clock Frequency4 tCORE ADuC842/ADuC843 Core Clock Period5 tCYC ADuC842/ADuC843 Machine Cycle Time6 32.768 kHz External Crystal Typ Max 30.52 6.26 6.26 9 9 0.131 16.78 0.476 0.059 0.476 7.63 Min
Unit s s s ns ns MHz s s
1
AC inputs during testing are driven at DVDD - 0.5 V for a Logic 1 and 0.45 V for Logic 0. Timing measurements are made at VIH min for Logic 1 and VIL max for Logic 0, as shown in Figure 87. 2 For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs. A port pin begins to float when a 100 mV change from the loaded VOH/VOL level occurs, as shown in Figure 87. 3 CLOAD for all outputs = 80 pF, unless otherwise noted. 4 ADuC842/ADuC843 internal PLL locks onto a multiple (512 times) of the 32.768 kHz external crystal frequency to provide a stable 16.78 MHz internal clock for the system. The core can operate at this frequency or at a binary submultiple called Core_Clk, selected via the PLLCON SFR. 5 This number is measured at the default Core_Clk operating frequency of 2.09 MHz. 6 ADuC842/ADuC843 machine cycle time is nominally defined as 1/Core_CLK.
Parameter ADuC841 CLOCK INPUT (External Clock Driven XTAL1) tCK XTAL1 Period tCKL XTAL1 Width Low tCKH XTAL1 Width High tCKR XTAL1 Rise Time tCKF XTAL1 Fall Time 1/tCORE ADuC841 Core Clock Frequency tCORE ADuC841 Core Clock Period tCYC ADuC841 Machine Cycle Time
Min 62.5 20 20
Variable External Crystal Typ Max 1000
0.131 0.05
tCKR
20 20 20 0.476 0.476 7.63
Unit ns ns ns ns ns MHz s s
tCKH
tCKL tCK
tCKF
Figure 86. XTAL1 Input
DVDD - 0.5V
VLOAD VLOAD + 0.1V
VLOAD VLOAD - 0.1V
0.45V
Figure 87. Timing Waveform Characteristics
Rev. 0 | Page 78 of 88
03260-0-086
0.2DVDD + 0.9V TEST POINTS 0.2DVDD - 0.1V
VLOAD - 0.1V
TIMING REFERENCE POINTS
VLOAD - 0.1V
03260-0-085
ADuC841/ADuC842/ADuC843
Parameter EXTERNAL DATA MEMORY READ CYCLE tRLRH RD Pulse Width tAVLL Address Valid after ALE Low tLLAX Address Hold after ALE Low tRLDV RD Low to Valid Data In tRHDX Data and Address Hold after RD tRHDZ Data Float after RD tLLDV ALE Low to Valid Data In tAVDV Address to Valid Data In tLLWL ALE Low to RD or WR Low tAVWL Address Valid to RD or WR Low tRLAZ RD Low to Address Float tWHLH RD or WR High to ALE High 16 MHz Core Clk Max 8 MHz Core Clock Max
Min 60 60 145 0
Min 125 120 290 0
48 150 170 230 130 190 15 60 120 255 375
100 625 350 470
35
Unit ns ns ns Ns ns ns ns ns ns ns ns ns
ALE (O)
t WHLH
PSEN (O)
tLLDV tLLWL t RLRH
RD (O)
tAVWL tRLDV tAVLL tLLAX tRLAZ tRHDX
DATA (IN)
tRHDZ
PORT 0 (I/O)
A0 A7 (OUT)
tAVDV
03260-0-087
PORT 2 (O)
A16 A23
A8 A15
Figure 88. External Data Memory Read Cycle
Rev. 0 | Page 79 of 88
ADuC841/ADuC842/ADuC843
Parameter EXTERNAL DATA MEMORY WRITE CYCLE tWLWH WR Pulse Width tAVLL Address Valid after ALE Low tLLAX Address Hold after ALE Low tLLWL ALE Low to RD or WR Low tAVWL Address Valid to RD or WR Low tQVWX Data Valid to WR Transition tQVWH Data Setup before WR tWHQX Data and Address Hold after WR tWHLH RD or WR High to ALE High 16 MHz Core Clk Max 8 MHz Core Clock Max
Min 65 60 65 190 60 120 380 60
Min 130 120 135 375 120 250 755 125
130
260
Unit ns ns ns ns ns ns ns ns ns
ALE (O)
tWHLH
PSEN (O)
t LLWL
WR (O)
t WLWH
t AVWL t LLAX t QVWX t QVWH
DATA
tWHQX
tAVLL
A0 A7
PORT 2 (O)
A16 A23
V8 A15
Figure 89. External Data Memory Write Cycle
Rev. 0 | Page 80 of 88
03260-0-088
ADuC841/ADuC842/ADuC843
Parameter I2C COMPATIBLE INTERFACE TIMING tL SCLOCK Low Pulse Width tH SCLOCK High Pulse Width tSHD Start Condition Hold Time tDSU Data Setup Time tDHD Data Hold Time tRSU Setup Time for Repeated Start tPSU Stop Condition Setup Time tBUF Bus Free Time between a Stop Conditionand a Start Condition tR Rise Time of Both SCLOCK and SDATA tF Fall Time of Both SCLOCK and SDATA tSUP1 Pulse Width of Spike Suppressed
1
Min 1.3 0.6 0.6 100 0.6 0.6 1.3
Max
0.9
300 300 50
Unit s s s s s s s s ns ns ns
Input filtering on both the SCLOCK and SDATA inputs suppresses noise spikes less than 50 ns.
tBUF
SDATA (I/O)
tSUP
MSB LSB ACK
tR
MSB
tDSU tPSU
SCLK (I)
PS STOP START CONDITION CONDITION
tDHD tSHD
1 2-7 8
tDSU tH
9
tDHD tRSU
tF tR
1
S(R) REPEATED START
tF
Figure 90. I2C Compatible Interface Timing
Rev. 0 | Page 81 of 88
03260-0-091
tL
tSUP
ADuC841/ADuC842/ADuC843
Parameter SPI MASTER MODE TIMING (CPHA = 1) tSL SCLOCK Low Pulse Width1 tSH SCLOCK High Pulse Width1 tDAV Data Output Valid after SCLOCK Edge tDSU Data Input Setup Time before SCLOCK Edge tDHD Data Input Hold Time after SCLOCK Edge tDF Data Output Fall Time tDR Data Output Rise Time tSR SCLOCK Rise Time tSF SCLOCK Fall Time
1
Min
Typ 476 476
Max
50 100 100 10 10 10 10 25 25 25 25
Unit ns ns ns ns ns ns ns ns ns
Characterized under the following conditions: a. Core clock divider bits CD2, CD1, and CD0 bits in PLLCON SFR set to 0, 1, and 1, respectively, i.e., core clock frequency = 2.09 MHz. b. SPI bit-rate selection bits SPR1 and SPR0 in SPICON SFR set to 0 and 0, respectively.
SCLOCK (CPOL = 0) SCLOCK (CPOL = 1)
tSH
tSL tSR tSF
tDAV
MOSI MSB
tDF
tDR
BITS 6-1 LSB
MISO
MSB IN
BITS 6-1
LSB IN
03260-0-092
tDSU
tDHD
Figure 91. SPI Master Mode Timing (CPHA = 1)
Rev. 0 | Page 82 of 88
ADuC841/ADuC842/ADuC843
Parameter SPI MASTER MODE TIMING (CPHA = 0) tSL SCLOCK Low Pulse Width1 tSH SCLOCK High Pulse Width1 tDAV Data Output Valid after SCLOCK Edge tDOSU Data Output Setup before SCLOCK Edge tDSU Data Input Setup Time before SCLOCK Edge tDHD Data Input Hold Time after SCLOCK Edge tDF Data Output Fall Time tDR Data Output Rise Time tSR SCLOCK Rise Time tSF SCLOCK Fall Time
1
Min
Typ 476 476
Max
50 150 100 100 10 10 10 10 25 25 25 25
Unit ns ns ns ns ns ns ns ns ns ns
Characterized under the following conditions: a. Core clock divider bits CD2, CD1, and CD0 bits in PLLCON SFR set to 0, 1, and 1, respectively, i.e., core clock frequency = 2.09 MHz. b. SPI bit-rate selection bits SPR1 and SPR0 in SPICON SFR set to 0 and 0, respectively.
SCLOCK (CPOL = 0) SCLOCK (CPOL = 1)
tSH
tSL tSR tSF
tDAV tDOSU
MOSI MSB BITS 6-1 LSB
tDF
tDR
MISO
MSB IN
BITS 6-1
LSB IN
03260-0-093
tDSU
tDHD
Figure 92. SPI Master Mode Timing (CPHA = 0)
Rev. 0 | Page 83 of 88
ADuC841/ADuC842/ADuC843
Parameter SPI SLAVE MODE TIMING (CPHA = 1) tSS SS to SCLOCK Edge tSL SCLOCK Low Pulse Width tSH SCLOCK High Pulse Width tDAV Data Output Valid after SCLOCK Edge tDSU Data Input Setup Time before SCLOCK Edge tDHD Data Input Hold Time after SCLOCK Edge tDF Data Output Fall Time tDR Data Output Rise Time tSR SCLOCK Rise Time tSF SCLOCK Fall Time tSFS SS High after SCLOCK Edge
Min 0
Typ 330 330
Max
50 100 100 10 10 10 10 0 25 25 25 25
Unit ns ns ns ns ns ns ns ns ns ns ns
SS
tSS
SCLOCK (CPOL = 0)
tSFS
tSH
SCLOCK (CPOL = 1)
tSL
tSR
tSF
tDAV
MISO MSB
tDF
tDR
BITS 6-1 LSB
tDSU
tDHD
Figure 93. SPI Slave Mode Timing (CPHA = 1)
Rev. 0 | Page 84 of 88
03260-0-094
MOSI
MSB IN
BITS 6-1
LSB IN
ADuC841/ADuC842/ADuC843
Parameter SPI SLAVE MODE TIMING (CPHA = 0) tSS SS to SCLOCK Edge tSL SCLOCK Low Pulse Width tSH SCLOCK High Pulse Width tDAV Data Output Valid after SCLOCK Edge tDSU Data Input Setup Time before SCLOCK Edge tDHD Data Input Hold Time after SCLOCK Edge tDF Data Output Fall Time tDR Data Output Rise Time tSR SCLOCK Rise Time tSF SCLOCK Fall Time tDOSS Data Output Valid after SS Edge tSFS SS High after SCLOCK Edge
Min 0
Typ 330 330
Max
50 100 100 10 10 10 10 25 25 25 25 20
Unit ns ns ns ns ns ns ns ns ns ns ns ns
SS
tSS
SCLOCK (CPOL = 0)
tSFS
tSH
SCLOCK (CPOL = 1)
tSL tSR tSF
tDAV tDOSS tDF
MISO MSB
tDR
BITS 6-1 LSB
MOSI
MSB IN
BITS 6-1
LSB IN
03260-0-095
tDSU
tDHD
Figure 94. SPI Slave Mode Timing (CPHA = 0)
Rev. 0 | Page 85 of 88
ADuC841/ADuC842/ADuC843 OUTLINE DIMENSIONS
1.03 0.88 0.73 2.45 MAX
39
14.15 13.90 SQ 13.65
27 26
SEATING PLANE
40
7.80 REF
TOP VIEW
(PINS DOWN)
10.20 10.00 SQ 9.80
VIEW A
52
PIN 1 14 1 13
2.10 2.00 1.95
7 0 0.13 MIN COPLANARITY
VIEW A
ROTATED 90 CCW
0.23 0.11
0.65 BSC
0.38 0.22
COMPLIANT TO JEDEC STANDARDS MO-112-AC-1
Figure 95. 52-Lead Plastic Quad Flatpack [MQFP] (S-52) Dimensions shown in millimeters
8.00 BSC SQ
0.60 MAX 0.60 MAX
43 42
0.30 0.23 0.18
56 1
PIN 1 INDICATOR
PIN 1 INDICATOR
TOP VIEW
7.75 BSC SQ
BOTTOM VIEW
6.25 6.10 SQ 5.95
0.50 0.40 0.30
29 28
15 14
0.25 MIN 1.00 0.85 0.80
12 MAX
0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM 0.50 BSC
6.50 REF
SEATING PLANE
0.20 REF
COPLANARITY 0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VLLD-2
Figure 96. 56-Lead Frame Chip Scale Package [LFCSP] 8 mm x 8 mm Body (CP-56) Dimensions shown in millimeters
Rev. 0 | Page 86 of 88
ADuC841/ADuC842/ADuC843 ORDERING GUIDES
Table 42. ADuC841 Ordering Guide
Model ADuC841BS62-5 ADuC841BS62-3 ADuC841BCP62-5 ADuC841BCP62-3 ADuC841BCP8-5 ADUC841BCP8-3 EVAL-ADuC841QS EVAL-ADuC841QSP2 Supply Voltage VDD 5 3 5 3 5 3 5 5 User Program Code Space 62 62 62 62 8 8 Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Description 52-Lead Plastic Quad Flatpack 52-Lead Plastic Quad Flatpack 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package QuickStart Development System QuickStart Plus Development System Package Option S-52 S-52 CP-56 CP-56 CP-56 CP-56
Table 43. ADuC842 Ordering Guide
Model ADuC842BS62-5 ADuC842BS62-3 ADuC842BCP62-5 ADuC842BCP62-3 ADuC842BCP32-5 ADuC842BCP32-3 ADuC842BCP8-5 ADuC842BCP8-3 EVAL-ADuC842QS EVAL-ADuC842QSP2 Supply Voltage VDD 5 3 5 3 5 3 5 3 5 5 User Program Code Space 62 62 62 62 32 32 8 8 Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Description 52-Lead Plastic Quad Flatpack 52-Lead Plastic Quad Flatpack 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package QuickStart Development System QuickStart Plus Development System Package Option S-52 S-52 CP-56 CP-56 CP-56 CP-56 CP-56 CP-56
Table 44. ADuC843 Ordering Guide
Model ADuC843BS62-5 ADuC843BS62-3 ADuC843BCP62-5 ADuC843BCP62-3 ADuC843BCP32-5 ADuC843BCP32-3 ADuC843BCP8-5 ADuC843BCP8-3 EVAL-ADuC842QS1 EVAL-ADuC842QSP1, 2
1
Supply Voltage VDD 5 3 5 3 5 3 5 3 5 5
User Program Code Space 62 62 62 62 32 32 8 8
Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C
Package Description 52-Lead Plastic Quad Flatpack 52-Lead Plastic Quad Flatpack 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package 56-Lead Chip Scale Package QuickStart Development System QuickStart Plus Development System
Package Option S-52 S-52 CP-56 CP-56 CP-56 CP-56 CP-56 CP-56
The only difference between the ADuC842 and ADuC843 parts is the voltage output DACs on the ADuC842; thus the evaluation system for the ADuC842 is also suitable for the ADuC843. 2 The Quickstart Plus system can only be ordered directly from Accutron. It can be purchased from the website www.accutron.com.
Rev. 0 | Page 87 of 88
ADuC841/ADuC842/ADuC843 Notes
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
(c) 2003 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C03260-0-11/03(0)
Rev. 0 | Page 88 of 88

▲Up To Search▲

Price & Availability of ADUC841BCP8-3

	To Download ADUC841BCP8-3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .